FACA AAC AC-SIMILE LE - Nilfisk PARTS - Nilfisk-Advance
FACA AAC AC-SIMILE LE - Nilfisk PARTS - Nilfisk-Advance
FACA AAC AC-SIMILE LE - Nilfisk PARTS - Nilfisk-Advance
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
USER MANUAL<br />
8. Remove the screw (19, Fig. F) and open the right tank<br />
(17) outwards.<br />
WARNING!<br />
Open the tanks (17 and 21, Fig. F) outwards,<br />
only if they are empty: each tank contains 115<br />
kg of water approximately.<br />
9. Loosen the drive system pump screw (1, Fig. N) two<br />
turns.<br />
10. Set the machine to working mode, by performing steps<br />
3, 4, 5, 7 and 8 in the reverse order.<br />
11. Tow the machine.<br />
12. When the machine towing is completed:<br />
– Perform steps 3, 4, 5, 7 and 8.<br />
– Install the screw (1, Fig. N).<br />
– Perform steps 3, 4, 5, 7 and 8 in the reverse order.<br />
TRANSPORTING BY TRAI<strong>LE</strong>R<br />
To transport the machine with a trailer, use the hooks and<br />
anchors shown below.<br />
WARNING!<br />
Machine anchor must be performed by<br />
qualified personnel.<br />
Available hooks<br />
1. The machine is equipped with the following hooks:<br />
– No.1 front towing/anchor hook (1, Fig. B)<br />
– No.1 rear anchor hook (2, Fig. B)<br />
Anchor<br />
2. To anchor the machine in case of trailer transport,<br />
proceed as described below:<br />
– Set the machine to transport mode (see the<br />
procedure in the relevant paragraph).<br />
– Remove the ignition key (17, Fig. D).<br />
– Engage the parking brake (7, Fig. E).<br />
– Close all lids, panels, etc.<br />
– Anchor the machine with the front and rear towing<br />
hooks (1 and 2, Fig. B).<br />
– Anchor the machine with two suitable bands (4 and<br />
5, Fig. B), placed over the rear axle support (6), and<br />
on the front left and right cab footboards (3)<br />
respectively.<br />
M<strong>AC</strong>HINE STORAGE<br />
If you foresee that the machine will not be used for more than<br />
30 days, proceed as follows:<br />
1. Empty the dust control system water tanks according to<br />
the following procedure:<br />
2. Prepare the machine, as shown in the After Machine<br />
Use paragraph.<br />
3. Store the machine indoor, in a clean and dry place,<br />
protected from bad weather conditions and with the<br />
following values:<br />
– Temperature: +1°C to +50°C<br />
– Humidity: max. 95%<br />
4. Disconnect the negative connector from the battery (18,<br />
Fig. E).<br />
5. Handle the diesel engine as described in the relevant<br />
Manual.<br />
WARNING!<br />
When the machine is to be transported or<br />
stored at ambient temperatures below 0°C,<br />
check that water tanks are empty, disassemble<br />
and drain the water filter housing.<br />
FIRST PERIOD OF USE<br />
After the first period of use (first 8 hours) it is necessary to<br />
carry out the following operations:<br />
1. Check the fastening and connecting elements for proper<br />
tightening. Check the visible parts for integrity and leaks.<br />
2. After the first 50 working hours, perform checks and<br />
replacements shown in the Scheduled Maintenance<br />
Table.<br />
18 33014085(3)2006-06 A