Levelflex M FMP40 - Process Centre Of Excellence.

More documents

Recommendations

Info

Appendix Levelflex M FMP40 with HART/4...20 mA basic setup safety settings 00 01 tank properties standard aluminium tank plastic tank bypass / pipe coax probe concrete wall output on alarm MIN -10% 3.6mA MAX 110% 22mA hold user specific 002 010 11 Appendix 11.1 Operating menu HART (Display modul), ToF Tool medium cond. unknown DC: 1.4 … 1.6 DC: 1.6 … 1.9 DC: 1.9 … 2.5 DC: 2.5 … 4 DC: 4 … 7 DC: > 7 length adjustment 03 end of probe 030 probe length free tie down isolated tie down gnd. not modified linearisation extended calibr. output envelope curve display diagnostics system parameter 04 05 06 0E 09 0A 0C level/ullage. level CU ullage CU level DU ullage DU Selection mapping common delete map. commun.address plot settings envelope curve substracted signal mapping present error tag no. 040 050 060 0E1 0A0 0C0 003 process proper. standard fast change slow change test: no filter outp. echo loss alarm hold output on alarm 011 ramp %MB/min ramp %span/min enter value enter value modified linearisation linear horizontal cyl manual semi-automatic table on clear table single curve cyclic 031 dist./meas.value 008 D and L is displayed no. of preambels recording curve language English Deutsch Francais Espanol Italiano Nederlands Katakana (japanese) previous error 041 061 0E2 092 0A1 probe covered free customer unit customer unit customer unit check distance distance = ok manual probe free dist. too small dist. unknown dist. too big low output limit off on back to home enter time Default: 900 s clear last error protocol + sw-no. delay time 014 in case of echo loss max. 4000 sec. default: 30 s empty calibr. enter value L00-FMP4xxxx-19-00-01-en-002 102 Endress + Hauser 004 012 013 032 probe length 033 042 042 042 051 062 093 0A2 0C2 end of probe 030 determine length 034 see Function group “leghth adjustment 03” probe length linearisation table no. input level input volume range of mapping input of mapping range pres. Map dist. is displayed curr. output mode standard fixed current current turn down format display decimal 1/16” reset for reset code see manual 033 043 043 044 045 052 054 063 094 0A3 determine length length OK too short too long next point no yes start mapping off on delete map. no yes fixed cur. value 034 005 4 mA value 068 20 mA value 069 no.of decimals x x.x x.xx x.xxx unlock parameter for enter code see manual serial no. 045 053 055 064 095 0A4 0C4
Levelflex M FMP40 with HART/4...20 mA Appendix full calibr. enter value safety distance 015 from blocking distance default: 0.1m max. scale max. scale dist./meas.value 008 D und L is displayed simulation sim. off sim. level sim. volume sim. current sep. character . point , comma measured dist. distance unit 006 dist./meas.value 008 check distance 051 range of mapping 052 start mapping 053 dist./meas.value 008 distance = ok input of off D and L D and L are displayed dist. too small manual probe free mapping range on are displayed 046 046 065 096 0A5 0C5 in safety dist. alarm warning self holding diameter vessel echo quality is displayed simulation value display test off on measured level download mode 016 047 056 066 097 0A6 0C8 dist. unknown dist. too big ackn. alarm 017 overspill protection 018 no yes offset will be added to the measured level output current 057 067 detection window 0A7 off on reset standard german WHG output damping application par. not modified modified brocken probe det off on upper block.dist L00-FMP4xxxx-19-00-02-en-002 Endress + Hauser 103 058 0A8 019 059 Return to Group Selection
Page 1 and 2:
Operating Instructions Levelflex M
Page 3 and 4:
Levelflex M FMP40 with HART/4...20
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52: Levelflex M FMP40 with HART/4...20
Page 101: Levelflex M FMP40 with HART/4...20
Page 107 and 108: P/SF/Konta XIV Declaration of Hazar
show all

Levelflex M FMP40 - Process Centre Of Excellence.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?