Sym Jet Euro X servicemanual - Scootergrisen

More documents

Recommendations

Info

Charging System JET 50 / JET 100 AC. Generator JET EURO 50 / JET EURO 100 Main Switch Fuse 15A Battery White Auto by- starter Yellow This chapter Contents Green/ Black Resistor 10.2Ω 5W Pink Resistor 5.9Ω 30W Green Green Red Black Regulator rectifier 15. ELECTRICAL EQUIPMENT Red Auto by- starter Resistor 8Ω 5W Green/ Black Yellow Yellow Yellow Yellow AC. Generator 15-5
15. ELECTRICAL EQUIPMENT Current Leakage Inspection Turn the main switch to OFF position, and remove the negative cable terminal (-) from the battery. Connect an ammeter between the negative cable terminal and the battery negative terminal. Caution In the current leakage test, set the current range at larger scale, then gradually decrease to the lower scale as the test process goes to avoid possible damage to the ammeter and the fuse. Do not turn the main switch to ON position during test. If the leaked current exceeds the specified value, it may indicate a short circuit. Allowable current leakage: Less than 1 mA Disconnect each cable one by one and take measurement of the current of each cable to locate the short circuit. Charging Voltage Inspection 15-6 Caution Before conducting the inspection, be sure that the battery is fully charged. If undercharged, the current changes dramatically. Use a fully charged battery having a voltage larger than 13.0 V While starting the engine, the starter motor draws large amount of current from the battery. After the engine is warmed up, replace original battery with a fully charged battery. Connect a digital voltmeter to the battery terminals. Connect an ammeter between both ends of the main fuse. Caution When the probe is reversibly connected, use an ammeter having an indication that shows both positive and negative direction current. The measurement would be at zero, if the ammeter is one direction only. This chapter Contents Ground circuit Caution Digital voltmeter Fuse connector Ammeter Battery (-) terminal Ammeter Do not use short-circuit cable. It is possible to measure the current by connecting an ammeter between the battery positive terminal and the + cable position terminal, however, while the starter motor is activated, the surge current of the motor draws from the battery may damage the ammeter. Use the kick starter to start the engine. The main switch shall be turned to OFF position during the process of inspection. Never tamper with the ammeter and the cable while there is current flowing through. It may damage the ammeter. Connect a tachometer. Turn on the headlight to high beam and start the engine. Accelerate the engine to the specified revolution per minute and measure the charging voltage. Specified Charging Current: 1.2 A / 5000 rpm Control Charging Voltage: 14.0~15.0 V / 5000 rpm
Page 1 and 2:
Forward Contents How To Use This Ma
Page 3 and 4:
How to Use This Manual This service
Page 5 and 6:
MODEL ILLUSTRATION JET 50 / 100 Ser
Page 9:
1. GENERAL INFORMATION General Safe
Page 14 and 15:
Torque values 1. GENERAL INFORMATIO
Page 17 and 18:
1. GENERAL INFORMATION 1-10 Starter
Page 19 and 20:
1. GENERAL INFORMATION 1-12 Fuel pu
Page 21 and 22:
1. GENERAL INFORMATION B. Engine ru
Page 23 and 24:
1. GENERAL INFORMATION E. CLUTCH, D
Page 25:
1. GENERAL INFORMATION Note: 1-18 T
Page 30:
Oil Pump Control Cable Caution To a
Page 35 and 36:
2. SERVICE MAINTENANCE INFORMATION
Page 39 and 40:
2. SERVICE MAINTENANCE INFORMATION
Page 41 and 42:
3. LUBRICATION SYSTEM Precautions I
Page 43 and 44:
3. LUBRICATION SYSTEM Oil Pump/Oil
Page 45 and 46:
3. LUBRICATION SYSTEM NOTES: 3-6 Th
Page 47 and 48:
4. ENGINE REMOVAL Engine removal Re
Page 49 and 50:
4. ENGINE REMOVAL Remove engine mou
Page 51 and 52:
5. CYLINDER HEAD/CYLINDER/PISTON Ma
Page 53 and 54:
5. CYLINDER HEAD/CYLINDER/PISTON Cy
Page 55 and 56:
5. CYLINDER HEAD/CYLINDER/PISTON Us
Page 58:
Maintenance Information ·····
Page 61 and 62:
6. ALTERNATOR Disconnect alternator
Page 63 and 64:
7. “V” TYPE BELT DRIVE SYSTEM/K
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 78 and 79:
Disassembly of Final Driving Mechan
Page 80 and 81:
Install countershaft, final driven
Page 82:
Maintenance Information······
Page 85 and 86:
9. CRANKCASE/CRANKSHAFT Crankshaft
Page 87 and 88:
9. CRANKCASE/CRANKSHAFT Assemble th
Page 90: Throttle Valve Removal Remove the b
Page 94 and 95: Flaot Level Inspection Measure floa
Page 96 and 97: Air Cleaner Removal/Installation Lo
Page 98 and 99: Front Disc Brake System ·····
Page 100 and 101: Maintenance Information Precautions
Page 102 and 103: Hydraulic Disc Brake Close the drai
Page 104 and 105: Brake Disc Inspection Visually chec
Page 106 and 107: Install the rubber pad into the gro
Page 108 and 109: Installation Apply with a thin coat
Page 110 and 111: Body Overview ··········
Page 112 and 113: Side Covers 1. Removal: Remove 3 s
Page 114 and 115: Remove 2 screw form of the body cov
Page 117 and 118: 12. BODY COVER Front Inner Box 1. R
Page 119 and 120: 12. BODY COVER Steering Handle Cove
Page 121 and 122: 12. BODY COVER Note: 12-12 This cha
Page 124 and 125: Steering Handle Removal Remove hand
Page 126 and 127: Inspection Place the axle onto a V-
Page 128 and 129: Lubricate the speedometer gear with
Page 130 and 131: Front Fork Removal Handle Front w
Page 132 and 133: Maintenance Information······
Page 134 and 135: Rear Wheel Remove Remove exhaust pi
Page 136 and 137: Maintenance Information······
Page 138: Troubleshooting No voltage Battery
Page 149 and 150: 15. ELECTRICAL EQUIPMENT Starter Mo
Page 152 and 153: Switch / Horn Remove handle covers
Page 154 and 155: Bulb Replacement Headlight/position
Page 156 and 157: Clock unit - JET EURO 50/100 Remove
Page 158 and 159: JET 50 ELECTRICAL DIAGRAM Home page
Page 160 and 161: JET 100 ELECTRICAL DIAGRAM Home pag
show all

Sym Jet Euro X servicemanual - Scootergrisen

Create successful ePaper yourself

Delete template?

Save as template?