Manual tehnic automate cafea Saeco Group 500

More documents

Recommendations

Info

English E16-CAPACITY alarm is just a simple warning, which does not block the machine, and indicates that the pump – solenoid valve circuit has detected a progressive decrease in water capacity. It can also indicate that the volumetric counter (fan) is defective or the existence of calcareous deposits on the solenoid valves. This condition means that a E04-PUMP failure is going to occur. Other warnings that do not block the machine are also foreseen and have the purpose of advising the user that the regeneration of resins of water softener, the grinders and filters is necessary. The number of counts beyond which the regeneration is deemed necessary is set in the OPTIONS menu; the display messages are: - * to indicate error E16 CAPACITY - α to indicate the regeneration of resins - & to indicate that filter replacement is required - $ to indicate that grinder replacement is required - # to indicate that filter and grinder replacement are required - % to indicate the regeneration of resins and replacement of grinders - Ω to indicate the regeneration of resins and replacement of filters - π to indicate the regeneration of resins and replacement of filters and grinders If one of the above mentioned symbols is displayed, by entering the SERVICE mode, the message ALARM will appear followed by the symbol for which maintenance is necessary. The safety device ‘group existence’ is also provided (microswitch installed on the boilergroup support). When the brew group is not in its position the machine displays SELECT BEVERAGE WITHOUT ESPRESSO COFFEE. 50
JP1/JP2 = EXPANSION BOARD CONNECTION JP3 = DISPLAY CONNECTOR JP4 = KEYS EXPANSION JP6 = POWER BOARD CONNECTOR JP7 = COUNTER JP8 = 24V VALIDATOR CONNECTOR JP9 = OBLITERATOR CONNECTOR J1 = PC PROGRAMMING CONNECTOR J2 = DATA COLLECTION CONNECTOR J3 = SAECO ELECTRONIC KEY CONNECTOR J4 = EXECUTIVE (MASTER) CONNECTOR J5 = PUSHBUTTON PANEL CONNECTOR J7 = CONN. 24V INPUT CONN. J8 = MDB CONNECTOR J9 = CONN. EXECUTIVE (SLAVE)CONNECTOR S1 = PROGRAMMING KEY S2 = SERVICE KEY LD1 = SERIAL PAYMENT SYSTEM CONNECTION LED LD2 = SUPPLY LED JMP1 = JUMPER FOR COIN 7 JMP2 = JUMPER FOR COIN 8 TR1 = DISPLAY CONTRAST REGULATION U1 = EPROM BASE U2 = CLOCK BASE English 51
Page 1 and 2: Automatic beverage vending machine
Page 3 and 4: TABLE OF CONTENTS 1 - INTRODUCTION
Page 5 and 6: Read This symbol indicates that the
Page 7 and 8: 1.4 Operator requirements To guaran
Page 9 and 10: - Operating reliability and the eff
Page 11 and 12: 5 - GENERAL TECHNICAL DESCRIPTION 5
Page 13 and 14: ESPRESSO COFFEE This process takes
Page 15 and 16: - Position the vending machine, che
Page 17 and 18: 6.4 Water mains connection Before c
Page 19 and 20: Warning The opening and possible sw
Page 21 and 22: fig.26 Warning IMPORTANT: When the
Page 23 and 24: - Make sure there are no lumps; do
Page 25 and 26: 6.8.5 Grounds bag insertion - remov
Page 27 and 28: 7 - PROGRAMMING With the programmin
Page 29 and 30: Maintenance - ‘Service’ mode Pr
Page 31 and 32: The example below shows how to perf
Page 33 and 34: Press ENTER again to confirm the se
Page 35 and 36: Change-giving function= option to g
Page 37 and 38: COINS This menu is accessed for pro
Page 39 and 40: 8 - SERVICE The service - maintenan
Page 41 and 42: 9 9 - - MAINTENANCE MAINTENANCE 9.1
Page 43 and 44: 9.1.3 Product loading When necessar
Page 45 and 46: - use the supplied key to rotate ma
Page 47 and 48: 10 10 - - INACTIVITY INACTIVITY If
Page 49: 12 12 - - TROUBLESHOOTING TROUBLESH
Page 53 and 54: Notes: English 53
Page 55 and 56: Notes: English 55

Manual tehnic automate cafea Saeco Group 500

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?