X515C DF & X510C Manual - Lowrance

More documents

Recommendations

Info

Reset Calibration highlighted (left). Reset Calibration confirmation window (right). To Reset Calibration: 1. Press MENU|MENU, select NMEA 2000 and press ENT. 2. Highlight FUEL MANAGEMENT and press ENT. 3. Highlight ENGINE SELECT and press ENT. The Engine Select menu will appear with up to four options: All Engines, Port, Center and Starboard. Selecting All Engines will reset calibration for all engines back to factory defaults. 4. Select All Engines or the engine connected to the desired device and press ENT. 5. Highlight RESET CALIBRATION and press ENT. The following message will appear: Are you sure you wish to Reset Calibration? 6. Highlight YES and press ENT. Press EXIT repeatedly to get back to the main display. 112
Section 6: Sonar Troubleshooting If your unit is not working, or if you need technical help, please use the following troubleshooting section before contacting the factory customer service department. It may save you the trouble of returning your unit for repair. For contact information, refer to the last page, just inside the back cover of this manual. Unit won't turn on 1. Check the power cable's connection at the unit. Also check the wiring. 2. Make sure the power cable is wired properly. The red wire connects to the positive battery terminal, black to negative or ground. 3. Check the fuse. 4. Measure the battery voltage at the unit's power connector. It should be at least 10 volts. If it isn't, the wiring to the unit is defective, the battery terminals or wiring on the terminals are corroded, or the battery needs charging. Unit freezes, locks up, or operates erratically 1. Electrical noise from the boat's motor, trolling motor, or an accessory may be interfering with the sonar unit. Rerouting the power and transducer cables away from other electrical wiring on the boat may help. Route the sonar unit's power cable directly to the battery instead of through a fuse block or ignition switch 2. Inspect the transducer cable for breaks, cuts, or pinched wires. 3. Check the transducer and power connector. Make sure it's securely plugged in to the unit. Weak bottom echo, digital readings erratic, or no fish signals 1. Make sure the transducer is pointing straight down. Clean the face of the transducer. Oil, dirt and fuel can cause a film to form on the transducer, reducing its effectiveness. If the transducer is mounted inside the hull, be sure it is shooting through only one layer of fiberglass and that it is securely bonded to the hull. When attaching a transducer to the inside of a hull, ONLY use the epoxy available from LEI (order information is inside the back cover). Do NOT use RTV silicone rubber adhesive or any other type of epoxy. The LEI epoxy is specially formulated so that it will cure properly for shoot-through applications. 113
Page 1 and 2:
www.lowrance.com Pub. 988-0151-451
Page 3 and 4:
Table of Contents Section 1: Read M
Page 5 and 6:
Radar..............................
Page 7 and 8:
Section 1: Read Me First! How this
Page 9 and 10:
Transmitter:....................X-5
Page 11 and 12:
For example, instructions for turni
Page 13 and 14:
Section 2: Installation & Accessori
Page 15 and 16:
oat hulls have a flat keel pad that
Page 17 and 18:
sonars.) Lack of angle adjustment c
Page 19 and 20:
Place the ratchets into the holes i
Page 21 and 22:
Transom Transom Position transducer
Page 23 and 24:
Trolling Motor Bracket Installation
Page 25 and 26:
WARNING: Do not remove any material
Page 27 and 28:
sure that your selected location wi
Page 29 and 30:
the transom. The bottom of the brac
Page 31 and 32:
The thinner branch with three wires
Page 33 and 34:
Power Diagram A To unit NMEA 2000 P
Page 35 and 36:
when not in use. Failure to connect
Page 37 and 38:
72.9 [2.87] 173.9 [6.85] 23.4 [0.92
Page 39 and 40:
PPP-15 Portable Power Pack with tra
Page 41 and 42:
Section 3: Basic Sonar Operation Th
Page 43 and 44:
Main Menu. Main Menu Commands There
Page 45 and 46:
• Colorline command: separates fi
Page 47 and 48:
Split zoom page (left) with split f
Page 49 and 50:
Basic Sonar Quick Reference 1. Depr
Page 51 and 52:
You can change the sensitivity leve
Page 53 and 54:
Other Free Training Aids The sonar
Page 55 and 56:
Section 4: Sonar Options & Other Fe
Page 57 and 58:
3. Press ↑ or ↓ to change the f
Page 59 and 60:
Sonar Alarms menu with Fish Alarm s
Page 61 and 62:
Sonar Page menu with ColorLine comm
Page 63 and 64:
Sonar Page menu with Depth Range co
Page 65 and 66:
Fish arches Area "zoomed" Normal di
Page 67 and 68: Fig. 1A Fig. 1B Many fish arches vi
Page 69 and 70: Sonar Features menu with a frequenc
Page 71 and 72: Local Time highlighted on Overlay D
Page 73 and 74: When you boost ping speed and switc
Page 75 and 76: Screen Command (left). Screen Menu
Page 77 and 78: Sonar Menu with Sensitivity command
Page 79 and 80: Set Language selected on main menu
Page 81 and 82: Full Sonar Chart. Overlay Data (dep
Page 83 and 84: Digital Data/Chart Customizing the
Page 85 and 86: Sonar with Custom Gauges The Sonar
Page 87 and 88: Radar When you access the Radar Pag
Page 89 and 90: There are three levels of surface c
Page 91 and 92: To adjust Transparency: 1. Press ME
Page 93 and 94: The first image (left) is a full so
Page 95 and 96: Section 5: NMEA 2000 Menu NMEA 2000
Page 97 and 98: When choosing an engine-tank config
Page 99 and 100: data window will include tank size
Page 101 and 102: To Reset Calibration: Choosing the
Page 103 and 104: Configuring EP Sensors All configur
Page 105 and 106: 3. Select the fuel flow you want to
Page 107 and 108: 3. Select the desired fluid level a
Page 109 and 110: Suzuki Engine Interface Configurati
Page 111 and 112: NOTE: The Suzuki Engine Interface D
Page 113 and 114: 3. Select the EP-15 Fluid Level and
Page 115 and 116: 1. Press MENU| MENU, use ↓ ↑ to
Page 117: 3. Highlight CALIBRATE TRIM and pre
Page 121 and 122: NOISE A major cause of sonar proble
Page 123 and 124: Notes 117
Page 125 and 126: LOWRANCE ELECTRONICS FULL ONE-YEAR
Page 127 and 128: Accessory Ordering Information for
show all

X515C DF & X510C Manual - Lowrance

Create successful ePaper yourself

Delete template?

Save as template?