X515C DF & X510C Manual - Lowrance

More documents

Recommendations

Info

NOTE These instructions will turn on FishTrack and Fish I.D. at the same time. To turn off FishTrack, repeat the instructions in step 2. Turning off FishTrack in this manner will not turn off Fish I.D. symbols. Symbols with FishTrack depths Sonar Features menu with Fish I.D. Depths selected (left). Sonar Page showing Fish I.D. symbols and FishTrack depths turned on (right). Frequency (Change Transducer Frequency) (X-515c<strong>DF</strong> only) The "<strong>DF</strong>" in your unit's name refers to its dual-frequency transducer, which operates with both 200 kHz and 50 kHz. The 200 kHz frequency has a 12° cone angle and the 50 kHz frequency has a 35° cone angle. The default frequency is 200 kHz, which is best for use in shallow water (about 300 feet or less). This frequency is the best choice for about 80 percent of the fresh and saltwater sport fishing applications. When you get into very deep saltwater – 300 to 500 feet or deeper – the 50 kHz frequency is the best choice. The 200 kHz transducer will give you better detail and definition, but less depth penetration. The 50 kHz transducer will give you greater depth penetration, but a little less detail and less definition. (Remember, all sonar units typically read deeper in fresh water than in saltwater.) There is a common exception to these rules. Some fishermen, who use downriggers on freshwater lakes (or the ocean), like to see their bait on the sonar. In many of those cases, you'll see a 50 kHz transducer frequency in use because the wider cone angle. 62
Sonar Features menu with a frequency of 200 kHz selected. To change the frequency setting to 50 kHz 1. From the Sonar Page, press MENU|↓ to SONAR FEATURES|ENT. 2. Press →|then press ↓ to 50 KHZ|ENT. 3. Press EXIT|EXIT to clear the menu. To change the frequency setting to 200 kHz 1. From the Sonar Page, press MENU|↓ to SONAR FEATURES|ENT. 2. Press →|then press ↓ to 200 KHZ|ENT. 3. Press EXIT|EXIT to clear the menu. HyperScroll See the entry on Ping Speed, which controls the HyperScroll feature. Noise Rejection See the entry on Advanced Signal Processing in this section. Overlay Data To change the digital data shown on top of the sonar page: 1. Press MENU|↓ to OVERLAY DATA|ENT. 2. Highlight (PRESS ENT TO ADD…) and press ENT. 63
Page 1 and 2:
www.lowrance.com Pub. 988-0151-451
Page 3 and 4:
Table of Contents Section 1: Read M
Page 5 and 6:
Radar..............................
Page 7 and 8:
Section 1: Read Me First! How this
Page 9 and 10:
Transmitter:....................X-5
Page 11 and 12:
For example, instructions for turni
Page 13 and 14:
Section 2: Installation & Accessori
Page 15 and 16:
oat hulls have a flat keel pad that
Page 17 and 18: sonars.) Lack of angle adjustment c
Page 19 and 20: Place the ratchets into the holes i
Page 21 and 22: Transom Transom Position transducer
Page 23 and 24: Trolling Motor Bracket Installation
Page 25 and 26: WARNING: Do not remove any material
Page 27 and 28: sure that your selected location wi
Page 29 and 30: the transom. The bottom of the brac
Page 31 and 32: The thinner branch with three wires
Page 33 and 34: Power Diagram A To unit NMEA 2000 P
Page 35 and 36: when not in use. Failure to connect
Page 37 and 38: 72.9 [2.87] 173.9 [6.85] 23.4 [0.92
Page 39 and 40: PPP-15 Portable Power Pack with tra
Page 41 and 42: Section 3: Basic Sonar Operation Th
Page 43 and 44: Main Menu. Main Menu Commands There
Page 45 and 46: • Colorline command: separates fi
Page 47 and 48: Split zoom page (left) with split f
Page 49 and 50: Basic Sonar Quick Reference 1. Depr
Page 51 and 52: You can change the sensitivity leve
Page 53 and 54: Other Free Training Aids The sonar
Page 55 and 56: Section 4: Sonar Options & Other Fe
Page 57 and 58: 3. Press ↑ or ↓ to change the f
Page 59 and 60: Sonar Alarms menu with Fish Alarm s
Page 61 and 62: Sonar Page menu with ColorLine comm
Page 63 and 64: Sonar Page menu with Depth Range co
Page 65 and 66: Fish arches Area "zoomed" Normal di
Page 67: Fig. 1A Fig. 1B Many fish arches vi
Page 71 and 72: Local Time highlighted on Overlay D
Page 73 and 74: When you boost ping speed and switc
Page 75 and 76: Screen Command (left). Screen Menu
Page 77 and 78: Sonar Menu with Sensitivity command
Page 79 and 80: Set Language selected on main menu
Page 81 and 82: Full Sonar Chart. Overlay Data (dep
Page 83 and 84: Digital Data/Chart Customizing the
Page 85 and 86: Sonar with Custom Gauges The Sonar
Page 87 and 88: Radar When you access the Radar Pag
Page 89 and 90: There are three levels of surface c
Page 91 and 92: To adjust Transparency: 1. Press ME
Page 93 and 94: The first image (left) is a full so
Page 95 and 96: Section 5: NMEA 2000 Menu NMEA 2000
Page 97 and 98: When choosing an engine-tank config
Page 99 and 100: data window will include tank size
Page 101 and 102: To Reset Calibration: Choosing the
Page 103 and 104: Configuring EP Sensors All configur
Page 105 and 106: 3. Select the fuel flow you want to
Page 107 and 108: 3. Select the desired fluid level a
Page 109 and 110: Suzuki Engine Interface Configurati
Page 111 and 112: NOTE: The Suzuki Engine Interface D
Page 113 and 114: 3. Select the EP-15 Fluid Level and
Page 115 and 116: 1. Press MENU| MENU, use ↓ ↑ to
Page 117 and 118: 3. Highlight CALIBRATE TRIM and pre
Page 119 and 120:
Section 6: Sonar Troubleshooting If
Page 121 and 122:
NOISE A major cause of sonar proble
Page 123 and 124:
Notes 117
Page 125 and 126:
LOWRANCE ELECTRONICS FULL ONE-YEAR
Page 127 and 128:
Accessory Ordering Information for
show all

X515C DF & X510C Manual - Lowrance

Create successful ePaper yourself

Delete template?

Save as template?