X515C DF & X510C Manual - Lowrance

More documents

Recommendations

Info

To use the simulator: 1. From a Sonar Page, press MENU|MENU|↓ to SONAR SIMULATOR|ENT. 2. Turn off the Sonar Simulator by pressing MENU|MENU|↓ to SONAR SIMULATOR|ENT|EXIT. NOTE: If you turn on your unit before attaching a transducer, it may enter a demo mode. The words "demo mode" flash on the bottom of the screen and a sonar chart plays much like the simulator. Unlike the simulator, the demo mode is for demonstration only, and will automatically stop as soon as you turn on the unit with a transducer attached. The simulator will continue to function normally. Stop Chart If you are running multiple units on a boat, there are times when you may want to turn off the sonar. This command turns off the sonar and stops the chart from scrolling. Sonar restarts automatically each time you turn on your unit. To Stop Chart from running: 1. Press MENU|↓ to STOP CHART|ENT|EXIT. To turn on sonar and start the chart scrolling again, repeat the above step. Sonar Menu with Stop Chart command selected. The box is unchecked, indicating the chart is scrolling across the screen. Surface Clarity The markings extending downward from the zero line on the chart are called "surface clutter." The clutter is caused by wave action, boat wakes, temperature inversion and more. The surface clarity control reduces or eliminates surface clutter signals. It does this by changing the sensitivity of the receiver, decreasing it near the surface and gradually increasing it as the depth increases. 82
There are three levels of surface clarity available: low, medium, or high. It can also be turned off. The default level is off. To adjust the Surface Clarity level 1. From the Sonar Page, press MENU|↓ to SONAR FEATURES|ENT. 2. Press ↓ to SURFACE CLARITY|ENT. 3. Press ↓ or ↑ to select clarity level|EXIT|EXIT|EXIT. Sonar Features menu with Sonar Features selected (left). Surface Clarity highlighted on Sonar Features menu (right). Surface clutter In the first illustration (left), Surface Clarity is turned off. The second example (right) Surface Clarity is set to High. Transducer Type (X-515c<strong>DF</strong> only) A dual-frequency unit includes a TRANSDUCER TYPE command. With this option you can tell your unit what type of transducer you're using, so it can properly interpret the signals it's receiving. 83
Page 1 and 2:
www.lowrance.com Pub. 988-0151-451
Page 3 and 4:
Table of Contents Section 1: Read M
Page 5 and 6:
Radar..............................
Page 7 and 8:
Section 1: Read Me First! How this
Page 9 and 10:
Transmitter:....................X-5
Page 11 and 12:
For example, instructions for turni
Page 13 and 14:
Section 2: Installation & Accessori
Page 15 and 16:
oat hulls have a flat keel pad that
Page 17 and 18:
sonars.) Lack of angle adjustment c
Page 19 and 20:
Place the ratchets into the holes i
Page 21 and 22:
Transom Transom Position transducer
Page 23 and 24:
Trolling Motor Bracket Installation
Page 25 and 26:
WARNING: Do not remove any material
Page 27 and 28:
sure that your selected location wi
Page 29 and 30:
the transom. The bottom of the brac
Page 31 and 32:
The thinner branch with three wires
Page 33 and 34:
Power Diagram A To unit NMEA 2000 P
Page 35 and 36:
when not in use. Failure to connect
Page 37 and 38: 72.9 [2.87] 173.9 [6.85] 23.4 [0.92
Page 39 and 40: PPP-15 Portable Power Pack with tra
Page 41 and 42: Section 3: Basic Sonar Operation Th
Page 43 and 44: Main Menu. Main Menu Commands There
Page 45 and 46: • Colorline command: separates fi
Page 47 and 48: Split zoom page (left) with split f
Page 49 and 50: Basic Sonar Quick Reference 1. Depr
Page 51 and 52: You can change the sensitivity leve
Page 53 and 54: Other Free Training Aids The sonar
Page 55 and 56: Section 4: Sonar Options & Other Fe
Page 57 and 58: 3. Press ↑ or ↓ to change the f
Page 59 and 60: Sonar Alarms menu with Fish Alarm s
Page 61 and 62: Sonar Page menu with ColorLine comm
Page 63 and 64: Sonar Page menu with Depth Range co
Page 65 and 66: Fish arches Area "zoomed" Normal di
Page 67 and 68: Fig. 1A Fig. 1B Many fish arches vi
Page 69 and 70: Sonar Features menu with a frequenc
Page 71 and 72: Local Time highlighted on Overlay D
Page 73 and 74: When you boost ping speed and switc
Page 75 and 76: Screen Command (left). Screen Menu
Page 77 and 78: Sonar Menu with Sensitivity command
Page 79 and 80: Set Language selected on main menu
Page 81 and 82: Full Sonar Chart. Overlay Data (dep
Page 83 and 84: Digital Data/Chart Customizing the
Page 85 and 86: Sonar with Custom Gauges The Sonar
Page 87: Radar When you access the Radar Pag
Page 91 and 92: To adjust Transparency: 1. Press ME
Page 93 and 94: The first image (left) is a full so
Page 95 and 96: Section 5: NMEA 2000 Menu NMEA 2000
Page 97 and 98: When choosing an engine-tank config
Page 99 and 100: data window will include tank size
Page 101 and 102: To Reset Calibration: Choosing the
Page 103 and 104: Configuring EP Sensors All configur
Page 105 and 106: 3. Select the fuel flow you want to
Page 107 and 108: 3. Select the desired fluid level a
Page 109 and 110: Suzuki Engine Interface Configurati
Page 111 and 112: NOTE: The Suzuki Engine Interface D
Page 113 and 114: 3. Select the EP-15 Fluid Level and
Page 115 and 116: 1. Press MENU| MENU, use ↓ ↑ to
Page 117 and 118: 3. Highlight CALIBRATE TRIM and pre
Page 119 and 120: Section 6: Sonar Troubleshooting If
Page 121 and 122: NOISE A major cause of sonar proble
Page 123 and 124: Notes 117
Page 125 and 126: LOWRANCE ELECTRONICS FULL ONE-YEAR
Page 127 and 128: Accessory Ordering Information for
show all

X515C DF & X510C Manual - Lowrance

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?