Owner's Manual SSP-600 Surround Processor - ClassÃ© Audio

More documents

Recommendations

Info

2 Menu button Pressing the front panel Menu button will call up the menu system, replacing the normal status display in the LCD touchscreen of the SSP-600. 3 LCD touchscreen Much of your interaction with the SSP-600 will be with the LCD touchscreen (and the SSP-600’s supplied remote control). It will usually display the various input selection buttons you would use in day-to-day operation, along with access to the tape monitor button. By pressing the Menu button, you can also call up the menu system of the SSP-600, which gives you control over many of the operational details of the surround processor, including system setup options, various display options (including the language in which the menu system itself displays), and several custom-installation capabilities that allow superior integration of the SSP-600 into complex systems. For more information, see the section The Menu System later in this manual. 4 Mute button The front panel Mute button reduces the volume of the surround processor to zero at the touch of a button. Pressing the button a second time restores the volume to its previous setting. The behavior of the mute can also be customized. Setup information on this feature is available in the Volume Setup section. However, if you increase the volume manually (using either the volume knob or the remote control) while the Mute button is engaged, the mute control will disengage and the volume will be reset to zero. This approach is a safety measure, to avoid situations in which the volume might be adjusted up while muted, only to then have the system un-muted to an unexpectedly high volume. 5 IR window The infrared (IR) receiver and transmitter are located behind this window. Ordinarily, your Classé SSP-600 must be able to “see” the remote control from this window in order to respond to remote control commands. If your surround processor will be located behind closed doors, or for any other reason will not be able to “see” the remote control during normal operation, you may use the rear panel IR input and an infrared repeater system to solve the problem. For more information about using an infrared repeater system to route signals to the SSP-600, refer to the section Rear Panel later in this manual, or contact your local Classé dealer. In addition to receiving IR commands, the SSP-600 can also transmit IR commands so they may be learned by third-party learning remote controls. The SSP-600 includes a comprehensive list of discrete IR commands to facilitate the creation of reliable macros. Specifically, there are discrete codes for all commands that normally operate as “toggle” functions (e.g. separate operate and standby commands in addition to the normal command that toggles between the two). 20
6 Volume Knob The large knob on the right side of the front panel of the SSP-600 is used to control the volume of the system. The volume is raised or lowered in precise 1dB increments throughout the range of the control most likely to be used while listening to music. At extremely low volumes, the step size is increased somewhat to make it easier to move quickly between extremely low and normal listening levels. 21
Page 1 and 2: Owner’s Manual SSP-600 Surround P
Page 3 and 4: Important Safety Instructions Cauti
Page 5 and 6: The Menu System ...................
Page 7 and 8: Unpacking and Placement unpacking y
Page 9 and 10: Operating Voltage The SSP-600 surro
Page 11 and 12: Special Design Features high-bandwi
Page 13 and 14: By contrast, most multichannel musi
Page 15 and 16: highly refined circuit design All C
Page 17 and 18: 5 Now you are ready to power up you
Page 19: Front Panel 1 Standby button & LED
Page 23 and 24: 1 Composite Video Inputs The SSP-60
Page 25 and 26: 5 Balanced Main Analog Audio Output
Page 27 and 28: 12 RS-232 Control Port This port ha
Page 29 and 30: 18 7.1 Channel Analog Audio Input A
Page 31 and 32: The Remote Control Your new surroun
Page 33 and 34: Understanding Surround Sound Today
Page 35 and 36: This compensation is provided by en
Page 37 and 38: Touching the mode button brings up
Page 39 and 40: position select The SSP-600 support
Page 41 and 42: Here, you can: • customize the be
Page 43 and 44: • high speed: determines the resp
Page 45 and 46: • The left button acts like the b
Page 47 and 48: speaker setup The Speaker Setup men
Page 49 and 50: • The name of each position can b
Page 51 and 52: display setup This button brings up
Page 53 and 54: The absolute system refers to the n
Page 55 and 56: cautionary note on Fkey use Note th
Page 57 and 58: 3. Only one speaker seems to be pla
Page 59 and 60: Specifications All specifications a
Page 62: Classé Audio 5070 François Cusson

Owner's Manual SSP-600 Surround Processor - ClassÃ© Audio

Create successful ePaper yourself

Delete template?

Save as template?