User Manual - TRS-RenTelco

More documents

Recommendations

Info

Appendix A: Specifications Table A- 10: Certifications and compliances (cont.) Category Safety Certification Compliance Equipment Type Safety Class IEC 1000 -4 -3 Standards or description Test and measuring UL61010, CSA -22.2 No. 1010.1, EN61010 -1, Class 1 (as defined in IEC 61010-1/A2) - grounded product RF field immunity 3V/m,80MHzto1GHz 80% amplitude modulated with a 1 kHz sinewave Performance criteria: The noise floor of the VM5000 with MIU is degraded up to 30dB while exposed to 3 V/m electric fields. This degradation is a function of both the electric field frequency and polarization; see Figure A -1 for a graph of typical behavior. For critical VM5000 Noise measurements in an environment where electric field levels are unknown it is recommended that the VM5000 Noise Floor be determined. This will show if any impairment is present for Noise measurements. See the VM5000 Option VGA Performance Verification for this procedure on page B -24. Figure A- 1: Graph of Immunity behavior A-18 VM5000 Automatic Video Measurement Set User Manual
Appendix A: Specifications Option SD/HD Tables A -11 and A -12 provide characteristics specific to Option SD/HD. Table A- 11: Video measurement specifications Characteristic Description Color bar measurement accuracy ±2.0 mV ±1.5 % of reading Noise measurement Unweighted Weighted Noise floor Multiburst measurement Flag amplitude Range and Accuracy -20 to -60 dB, ±1dB (30 MHz measurement bandwidth) -60 to -70 dB, ±2dB (30 MHz measurement bandwidth) -20 to -60 dB, ±1dB -60 to -70 dB, ±2dB < -76 dB, 30 MHz noise bandwidth Accuracy ±2mV±1.5% of reading Measurement of all 8 bar levels, displayed in absolute (mV) values. YPbPr or RGB formats. Noise measurement bandwidth selectable, 200 KHz to 250 MHz. Trigger on CH 4 required for measurements below -60 dB (30 MHz BW). Unified Weighting Filter. Trigger on CH 4 required for measurements below -60 dB. Typical < -80 dB, 30 MHz noise bandwidth 1 MHz to 10 MHz packets ±0.5 dB Measurement relative to reference flag amplitude 10 to 30 MHz packets ±0.75 dB Frequency readout ±0.1 MHz Multiburst packet frequency is measured and displayed. VM5000 Automatic Video Measurement Set User Manual A-19
Page 1 and 2:
User Manual VM5000 Automatic Video
Page 3:
Warranty 2 Tektronix warrants that
Page 6 and 7:
Table of Contents Reference Display
Page 8 and 9:
Table of Contents Index Option SD/H
Page 10 and 11:
Table of Contents Figure 2 -17: Cal
Page 12 and 13:
Table of Contents Figure 3 -60: Lim
Page 14 and 15:
Table of Contents Table B -1: Requi
Page 16 and 17:
Table of Contents xii VM5000 Automa
Page 18 and 19:
Preface Related Manuals and Online
Page 20 and 21:
General Safety Summary Symbols and
Page 22 and 23:
Environmental Considerations xviii
Page 25 and 26:
Product Description This manual sup
Page 27 and 28:
Product Description Compatibility o
Page 29 and 30:
Installation This section addresses
Page 31 and 32:
Installation Connecting the Mouse T
Page 33 and 34:
Installation Creating an Emergency
Page 35 and 36:
Installation Desktop Applications Y
Page 37 and 38:
Incoming Inspection This section co
Page 39 and 40:
Incoming Inspection 1. Set the vide
Page 41 and 42:
Incoming Inspection NOTE. These pro
Page 43 and 44:
Incoming Inspection Figure 1- 6: Re
Page 45 and 46:
Incoming Inspection Possible Errors
Page 47 and 48:
Options and Accessories This sectio
Page 49 and 50:
Options and Accessories Table 1- 3:
Page 51 and 52:
Options and Accessories Table 1- 3:
Page 53:
Operating Basics
Page 56 and 57:
Operating Basics The VM5000 selects
Page 58 and 59:
Operating Basics To achieve the bes
Page 60 and 61:
Operating Basics 4-Wire Video with
Page 62 and 63:
Operating Basics To connect the RGB
Page 64 and 65:
Operating Basics To connect the DUT
Page 66 and 67:
Operating Basics A pop-up warning a
Page 68 and 69:
Operating Basics 2 Figure 2- 18: At
Page 70 and 71:
Operating Basics The Matrix Test Si
Page 72 and 73:
Operating Basics Figure 2 -24 shows
Page 74 and 75:
Operating Basics For other refresh
Page 76 and 77:
Operating Basics The VM5000 Applica
Page 78 and 79:
Operating Basics Setting the Input
Page 80 and 81:
Operating Basics 5. Select the appr
Page 82 and 83:
Operating Basics Setting the Measur
Page 84 and 85:
Operating Basics 5. Auto Scale fits
Page 86 and 87:
Operating Basics 9. (Option VGA) Th
Page 88 and 89:
Operating Basics Setting Reference
Page 90 and 91:
Operating Basics Displaying the Inp
Page 92 and 93:
Operating Basics 4. Sets the width
Page 94 and 95:
Operating Basics 3. Sets the video
Page 96 and 97:
Operating Basics 2. The instrument
Page 98 and 99:
Operating Basics Taking Measurement
Page 100 and 101:
Operating Basics 2. To change a val
Page 102 and 103:
Operating Basics 3. Enter a file na
Page 104 and 105:
Operating Basics 3. Select the Look
Page 106 and 107:
Operating Basics RTF: Use RTF (
Page 108 and 109:
Operating Basics 2-54 VM5000 Automa
Page 111 and 112:
Reference Overview This chapter pro
Page 113 and 114:
Menu Descriptions The following tab
Page 115 and 116:
Menu Descriptions Configuration Men
Page 117 and 118:
Menu Descriptions Menu Item Functio
Page 119 and 120:
Menu Descriptions Menu Item Functio
Page 121 and 122:
Menu Descriptions Command Measureme
Page 123 and 124:
Menu Descriptions Command Reference
Page 125 and 126:
Menu Descriptions Command Function
Page 127 and 128:
Menu Descriptions Menu item Color B
Page 129 and 130:
Menu Descriptions Menu item Non Lin
Page 131 and 132:
Menu Descriptions Command Ch -Ch Sk
Page 133 and 134:
Menu Descriptions Command Luma Leve
Page 135 and 136:
Menu Descriptions Utilities Menu CA
Page 137 and 138:
Option SD/HD Detailed Measurement I
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Option VGA Detailed Measurement Inf
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Setting Up Measurements There are t
Page 171 and 172:
Setting Up Measurements 5. Select E
Page 173 and 174:
Setting Up Measurements Option SD/H
Page 175 and 176:
Setting Up Measurements 5. Select E
Page 177 and 178:
Setting Up Measurements The easiest
Page 179 and 180:
Page 181 and 182:
Setting Up Measurements 2. To chang
Page 183 and 184:
Page 185 and 186:
Setting Up Measurements 1. Select R
Page 187 and 188:
Setting Up Measurements Setting Up
Page 189 and 190:
Setting Up Measurements Setting Up
Page 191 and 192:
Page 193 and 194:
Setting Up Measurements Figure 3- 1
Page 195 and 196:
Setting Up Measurements The next ti
Page 197 and 198:
Setting Up Measurements 3. Click th
Page 199 and 200:
Setting Up Measurements Turn the
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Setting Up Measurements Turn the
Page 209 and 210:
Viewing Measurement Results Use the
Page 211 and 212:
Viewing Measurement Results Display
Page 213 and 214: Viewing Measurement Results Referen
Page 215 and 216: Viewing Measurement Results Select
Page 219 and 220: Viewing Measurement Results Click t
Page 221 and 222: Viewing Measurement Results Display
Page 239 and 240: Viewing Measurement Results Measure
Page 243 and 244: Viewing Measurement Results To disp
Page 245: Appendices
Page 248 and 249: Appendix A: Specifications Table A-
Page 268 and 269: Appendix A: Specifications Option V
Page 272 and 273: Appendix A: Specifications A-26 VM5
Page 274 and 275: Appendix B: Performance Verificatio
Page 314 and 315:
Appendix B: Performance Verificatio
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Appendix C: Cleaning Clean the flat
Page 322 and 323:
Appendix D: Rebuilding the Hard Dri
Page 324 and 325:
Appendix E: Signal Sources Package
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 333 and 334:
Index Numbers 3-wire composite sync
Page 335 and 336:
Index Linearity detailed measuremen
Page 337 and 338:
Index TG700 DNL files, Matrix test
Page 339 and 340:
Read This First VM5000 Automatic Vi
Page 341 and 342:
Read This First This following proc
Page 343 and 344:
Read This First Table 1: Equipment
Page 345 and 346:
Read This First NOTE. If typed keyb
Page 347 and 348:
Read This First 6. Connect the BNC
Page 349 and 350:
Read This First 25. Using Hyperterm
Page 351 and 352:
Read This First 10. On the VM5000 f
Page 353 and 354:
Read This First 5. Set the spectrum
Page 355 and 356:
Read This First Optional Checks to
Page 357 and 358:
Read This First in Table 4, column
Page 359 and 360:
Read This First MIU G input BNC to
Page 361 and 362:
Read This First 8. Disconnect the M
show all

User Manual - TRS-RenTelco

Create successful ePaper yourself

Delete template?

Save as template?