C:\Documents and Settings\Allen - MSAWorld.com

More documents

Recommendations

Info

QUICK REFERENCE SHEET Component Resistances* Electric Models Gas Models Drive motor (120 volt, 60 Hz, 1/4 h.p. 1725 rpm) Motor Start Winding Motor Run Winding Heating Element 4.5 Ohms 3.8 Ohms 12.8 Ohms 4.5 Ohms 3.8 Ohms Burner Assembly Ignitor Secondary Coil Booster Coil --- --- --- 50 - 400 Ohms 1200 Ohms 1320 Ohms * +/- 10% @ 77° F 8
SAMPLE WIRING DIAGRAM FOR ELECTRIC MODELS CAUTION: DISCONNECT ELECTRIC CURRENT BEFORE SERVICING. LABELALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPERAND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING. L1 240 VAC 120 VAC 120 VAC L2 RED ACCUMULATOR TM BLUE BLUE CABINET BLUE N GRN WIRE NOT INCLUDED IN MODELS PROVIDED WITH 4 - WIRE POWER CORD. C NO DOOR SWITCH GRAY BLK 6 2 RED A WHT WHT WHT THERMAL LIMITER WHT 4 START RUN MOTOR 5 GRAY 1 GRN FABRIC SELECTOR SWITCH INDICATOR LIGHT YEL TAN TAN START SWITCH CABINET BASE YEL HEATER 4500 WATTS B 3 K 4 5 BLUE 28K ORG/BLK BLK ORG CONTROL THERMOSTAT ORG/BLK SAFETY THERMOSTAT GRN GRN CABINET COIN BOX CABINET TOP PANEL 1ACCUMULATION. DRIVE MOTOR HEATER NOTES: 1. All wiring must conform to local electrical codes. 2. Connect dryer to a 30 amp individual branch circuit. 3. Motor at rest, thermostat closed <strong>and</strong> fabric selector switch at regular. WIRING CODES QUICK DISCONNECT TERMINALS CONNECTION NO CONNECTION MOTOR SWITCH SPLICE MOTOR PROTECTOR CHASSIS (CABINET) GROUND SCREW TERMINAL HARNESS CONNECTOR TERMINAL INSULATED TERMINAL TRANSIENT VOLT SUPPRESSOR FABRIC SELECTOR. SWITCH FUNCTION RESISTANCE HIGH INFINITY MEDIUM 3K +/-5% LOW 10 MAX 9
Page 1 and 2: ELECTROLUX MAJOR APPLIANCES OF NORT
Page 3 and 4: SAFE SERVICING PRACTICES 2 QUICK RE
Page 5 and 6: Removing temperature knob 53 Removi
Page 7: QUICK REFERENCE SHEET SPECIFICATION
Page 11 and 12: SECTION A - INSTALLATION INSTRUCTIO
Page 13 and 14: The following are specific requirem
Page 15 and 16: 4. A minimum of 120 square inches (
Page 17 and 18: stalled onto power cord. If the str
Page 19 and 20: 5. Attach the green power cord grou
Page 21 and 22: Commercial Appliance Warranty Infor
Page 23 and 24: CHANGING THE VEND PRICE ON A GREENW
Page 25 and 26: Meter Case Instructions and Parts L
Page 27 and 28: The body casting of the coin chute
Page 29 and 30: The drive cam arm, switch cam arm a
Page 31 and 32: Dryer section: Clothes dryers remov
Page 33 and 34: Airflow Since the moisture in the c
Page 35 and 36: Air leaks: Two types of air leaks m
Page 37 and 38: selector switch is set to the low h
Page 39 and 40: safety thermostat, line 1 is connec
Page 41 and 42: FAILURE Dryer runs as long as the s
Page 43 and 44: SECTION D - TEARDOWN This section w
Page 45 and 46: 5. Lift the (2) locking plates off.
Page 47 and 48: 6. To remove the slide stop, discon
Page 49 and 50: 14. To remove the dog stop slides,
Page 51 and 52: 3. Released a plastic rivet holding
Page 53 and 54: 2. Remove the drive cam and the tim
Page 55 and 56: Removing door hinges: To raise the
Page 57 and 58: Removing the coin box: 1. Disconnec
Page 59 and 60:
3. Remove the (2) screws, one on ea
Page 61 and 62:
3. Remove the hot melt glue and pul
Page 63 and 64:
Removing the ball hitch from the dr
Page 65 and 66:
Removing the control thermostat: 1.
Page 67 and 68:
Removing the igniter: (Gas dryers)
Page 69 and 70:
3. Lift the shield and duct out of
Page 71:
NOTES 71
show all

C:\Documents and Settings\Allen - MSAWorld.com

Create successful ePaper yourself

Delete template?

Save as template?