EWP Hangers - USP Connectors

Face Mount Hangers – THF series
EWP Hangers
Designed to provide lateral support for the top chords of I-Joists
in depths up to 16˝. Eliminates the need for web stiffeners in
most applications (see Web Stiffener Reqd. column in EWP
Face Mount Hanger Chart for specific applications).
Materials: See EWP Face Mount Hangers charts,
pages 121-122.
Finish: G90 galvanizing
Options: See Specialty Options chart.
Codes: Load values are derived from data submitted
to various North American building code
evaluators.
Installation:
• Use all specified fasteners. See Product Notes, page 10.
• Install 10d x 1 1 ⁄ 2˝ nails into joist through raised dimple at
a 30° to 45° angle.
• THF Min – Fill all round nail holes.
• THF Max – Fill all round and diamond holes.
Specialty Options Chart – refer to Specialty
Options pages 210 to 211 for additional details.
Typical THF I-Joist
to Joist installation
H
W
2˝
Additional diamond
nail holes for
maximum nailing
Standard round
nail holes for
minimum nailing
THF single
Option Skewed 1,3 Sloped Seat 2,3 Sloped / Skewed 1,2,3 Inverted Flange
Not available in
Range
See Sloped Seat and Skewed
Factored
Resistance
Ordering
100% of table load.
Add SK, angle required,
and right (R) or left (L),
to product number.
Example: THF23925-SK45R
100% of table load
Add SL, slope required,
and up (U) or down (D),
to product number.
Example: THF23925-SL30D
1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.
2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.
3) All sloped, skewed, or combinations require bevel cut on joist in all applications.
4) Modifications to THF hangers do not feature seat cleats.
80% of table load.
See Sloped Seat and Skewed
Example:
THF23925-SK45RSL30D
100% of table load.
nailing into the support
members end grain.
Add IF,
to product number.
Example: THF23925IF
Dimple allows
30˚ to 45˚
nailing
Typical THF double I-Joist
to LVL installation
Raised Dimple
nail holes allow
30° to 45°
nailing into
I-Joist bottom
flange.
W
D
H
THF double
Seat Cleat®
helps lock
I-Joist into place
for
positive seating
and nailing ease.
© Copyright 2013 USP Structural Connectors ®
Face Mount Hangers – HD series
Designed to to support LVL, LSL, and PSL beams and headers in medium load conditions.
Materials: See EWP Face Mount Hangers charts, pages 122-123.
Finish: G90 galvanizing
Options: See Specialty Options chart.
Codes: Load values are derived from data submitted
to various North American building code
evaluators.
Installation:
• Use all specified fasteners. See Product Notes, page 10.
• Drive bend line nails into header at 45° to achieve listed loads
Drive bend line nails
into header at 45° to
achieve listed loads.
Typical HD
bend line nail installation
Specialty Options Chart – refer to Specialty Options pages 210 to 211 for additional details.
Typical HD
installation
118
Option Skewed 1,3 Sloped Seat 2,3 Sloped / Skewed 1,2,3 Inverted Flange
See Sloped Seat and Not available in
Range
Skewed
Factored
Resistance
Ordering
100% of table load.
75% of uplift load on
Add SK, angle required,
and right (R) or left (L),
to product number.
Example: HD410-SK45R
100% of table load
Add SL, slope required,
and up (U) or down (D),
to product number.
Example: HD410-SL30D
80% of table load.
75% of uplift load on
See Sloped Seat and
Skewed
Example:
HD410-SK45RSL30D
100% of table load.
65% of table load when
nailing into the support
members end grain.
Add IF,
to product number.
Example: HD410IF
1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.
2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.
3) All sloped, skewed, or combinations require bevel cut on joist in all applications and web stiffeners with I-joists.
Hangers for square-cut joists are available as a Custom. Further reductions in allowable loads may apply.
4) Modifications of HD hangers may be manufactured as hot rolled, welded, or primed.
1-800-328-5934 • www.USPconnectors.com
Bend line
nailing
W
HD
H
D