EWP Hangers - USP Connectors

Power Nail Hangers – JN, JN(E), MRT7 & MTHF series
Designed for assembly line installation, these
hangers feature a generous flange area to
accommodate power nailer maneuvering.
Engineered for economical installation and
maximum load values.
NEW
© Copyright 2013 USP Structural Connectors ®
Materials: See chart
Finish: G90 galvanizing
Codes: Factored resistances are
derived from data submitted
to various North American
building code evaluators and
are in accordance
with CSA O86-09.
Installation:
• Install all fasteners with a pneumatic nailer.
See Product Notes, page 10.
• Nailing zones are distinguished by embossed
pattern.
• Install fasteners with care not to overdrive
fastener causing indentation of connector.
• Fastener quantities shall be installed
symmetrically on both sides of connector.
• Installer should reduce risk of injury from
rebounding fasteners by using personal eye
protection during fastener installation.
• Minimum center to center fastener spacing
is 1”.
Typical MRT7
installation
W
H
MRT7
Typical MTHF
installation
W
D
A
MTHF
H
Nailing
Zones
Typical JNE
installation
W
A
D
JN28E
(JN26E &
JN210E Similar)
H
USP
Stock No.
Dimensions (in) Fastener Schedule 1,2,3
Factored Resistance
Header
Joist
DF-L
S-P-F
Download F1 4 F2 4 Uplift 4 Download F1 4 F2 4 Uplift 4
Steel
Lbs kN Lbs kN Lbs kN Lbs kN Lbs kN Lbs kN Lbs kN Lbs kN
Ref. No. Gauge W H D A Qty Type Qty Type 100% 100% 115% 115% 115% 115% 115% 115% 100% 100% 115% 115% 115% 115% 115% 115%
3 "P" or "T" nails 3 "P" or "T" nails -- -- -- -- 85 0.38 85 0.38 360 1.60 -- -- -- -- 65 0.29 65 0.29 335 1.49
MRT7
-- -- -- --
4 "P" or "T" nails 4 "P" or "T" nails -- -- -- -- 115 0.51 115 0.51 480 2.14 -- -- -- -- 85 0.38 85 0.38 445 1.98
5 "P" or "T" nails 5 "P" or "T" nails -- -- -- -- 145 0.65 145 0.65 600 2.67 -- -- -- -- 105 0.47 105 0.47 555 2.47
MTHF25925 MMLUI39 20 2
MTHF25112 MMLUI311 20
JN26E MMLU26 20 4-13/16
2
2
6 "P" or "T" nails 6 "P" or "T" nails -- -- -- -- 175 0.78 175 0.78 720 3.20 -- -- -- -- 125 0.56 125 0.56 665 2.96
10 "P" or "T" nails 4 "P" or "T" nails 1460 6.49 -- -- -- -- -- -- -- -- 630 2.80 1250 5.56 -- -- -- -- -- -- -- -- 540 2.40
16 "P" or "T" nails 4 "P" or "T" nails 2215 9.85 -- -- -- -- -- -- -- -- 630 2.80 1900 8.45 -- -- -- -- -- -- -- -- 540 2.40
10 "P" or "T" nails 4 "P" or "T" nails 1460 6.49 -- -- -- -- -- -- -- -- 630 2.80 1250 5.56 -- -- -- -- -- -- -- -- 540 2.40
16 "P" or "T" nails 4 "P" or "T" nails 2215 9.85 -- -- -- -- -- -- -- -- 630 2.80 1900 8.45 -- -- -- -- -- -- -- -- 540 2.40
10 "P" or "T" nails 4 "P" or "T" nails 1460 6.49 -- -- -- -- -- -- -- -- 630 2.80 1250 5.56 -- -- -- -- -- -- -- -- 540 2.40
16 "P" or "T" nails 4 "P" or "T" nails 2215 9.85 -- -- -- -- -- -- -- -- 630 2.80 1900 8.45 -- -- -- -- -- -- -- -- 540 2.40
10 "P" or "T" nails 4 "P" or "T" nails 1460 6.49 -- -- -- -- -- -- -- -- 630 2.80 1250 5.56 -- -- -- -- -- -- -- -- 540 2.40
JN28E 20 6-11/16 2
16 "P" or "T" nails 4 "P" or "T" nails 2215 9.85 -- -- -- -- -- -- -- -- 630 2.80 1900 8.45 -- -- -- -- -- -- -- -- 540 2.40
20 "P" or "T" nails 4 "P" or "T" nails 2300 10.23 -- -- -- -- -- -- -- -- 630 2.80 1970 8.76 -- -- -- -- -- -- -- -- 540 2.40
JN210E
MMLU210,
MMLU211
20 2
JN26-2 MMLU26-2 2
JN28-2
2
10 "P" or "T" nails 4 "P" or "T" nails 1460 6.49 -- -- -- -- -- -- -- -- 630 2.80 1250 5.56 -- -- -- -- -- -- -- -- 540 2.40
16 "P" or "T" nails 4 "P" or "T" nails 2215 9.85 -- -- -- -- -- -- -- -- 630 2.80 1900 8.45 -- -- -- -- -- -- -- -- 540 2.40
20 "P" or "T" nails 4 "P" or "T" nails 2300 10.23 -- -- -- -- -- -- -- -- 630 2.80 1970 8.76 -- -- -- -- -- -- -- -- 540 2.40
10 "P" or "T" nails 6 "P" or "T" nails 1370 6.09 -- -- -- -- -- -- -- -- 1540 6.85 1175 5.23 -- -- -- -- -- -- -- -- 1320 5.87
16 "P" or "T" nails 6 "P" or "T" nails 3035 13.50 -- -- -- -- -- -- -- -- 1540 6.85 2600 11.57 -- -- -- -- -- -- -- -- 1320 5.87
10 "P" or "T" nails 6 "P" or "T" nails 1370 6.09 -- -- -- -- -- -- -- -- 1540 6.85 1175 5.23 -- -- -- -- -- -- -- -- 1320 5.87
16 "P" or "T" nails 6 "P" or "T" nails 3035 13.50 -- -- -- -- -- -- -- -- 1540 6.85 2600 11.57 -- -- -- -- -- -- -- -- 1320 5.87
24 "P" or "T" nails 6 "P" or "T" nails 3715 16.53 -- -- -- -- -- -- -- -- 1540 6.85 3185 14.17 -- -- -- -- -- -- -- -- 1320 5.87
2) Fasteners shall be pneumatically driven in such a way as firmly seats the nail head against the hanger steel, without embedding the nail head completely through the plane of the metal surface, or otherwise punching through.
New products or updated product information are designated in red font.
1-800-328-5934 • www.USPconnectors.com 205
USP2240-131
Manuf. Housing