EWP Hangers - USP Connectors
EWP Hangers - USP Connectors
EWP Hangers - USP Connectors
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Specialty Options & General Notes<br />
Specialty Options<br />
<strong>USP</strong><br />
Series<br />
Width<br />
Skewed (Maximum)<br />
Sloped Seat (Maximum)<br />
Sloped / Skewed<br />
Sloped Top Flange (Maximum)<br />
BPH all 50º 45º 45º <br />
GHF all 50º 45º <br />
67-1/2º<br />
HD 1<br />
45º<br />
50º<br />
67-1/2º<br />
HDO 45º<br />
50º<br />
Top Flange Offset<br />
Saddle Hanger<br />
Ridge Hanger (Maximum)<br />
Inverted Flange<br />
<br />
width ><br />
<br />
width ><br />
<br />
width ><br />
Uplift<br />
Weldability<br />
<strong>USP</strong> Series<br />
Catalog Page Reference<br />
124-125,<br />
128-129,<br />
132-136,<br />
138-142<br />
146<br />
90-96,<br />
<br />
118,<br />
122-123<br />
97,<br />
<br />
99-101<br />
HGU all 45º<br />
<br />
145<br />
width ><br />
HJC all 60º 173<br />
126,<br />
HLBH all 50º 45º 45º 45º 132-136,<br />
138-142<br />
<br />
89,<br />
HUS<br />
all<br />
width ><br />
91-95,<br />
<br />
119, 123,<br />
167<br />
HWUH all 45º 45º 106-107<br />
KB all <br />
97,<br />
100-101<br />
KEG all 45º 45º 147<br />
KGB all 148<br />
KGLS all 50º 45º 30º 150<br />
KGLST all 150<br />
KGLT all 50º 45º 45º 149<br />
KHGB all 148<br />
KHGLS all 50º 45º 30º 150<br />
KHGLST all 150<br />
KHGLT all 50º 45º 45º 149<br />
KHHB all 148<br />
KHW all 84º 45º 35º 45º <br />
98,<br />
100-101<br />
KLB all 97, 99<br />
KLEG all 45º 45º 147<br />
KMEG all 45º 45º 147<br />
LGU all 45º<br />
<br />
145<br />
width ><br />
LSSH all 45º 45º 103, 144<br />
MGU all 45º<br />
<br />
145<br />
width ><br />
MPH 1 60º 45º <br />
108,<br />
126-141<br />
MSHL/R all 45º 170<br />
PHM 1 all 84º 45º 35º 45º <br />
126-131,<br />
133-141<br />
PHXU 1 all 60º 45º 35º <br />
126-129,<br />
132-136,<br />
138-142<br />
SKH all 45º 104-105<br />
SKHH all 45º 104-105<br />
SUH<br />
67-1/2º<br />
88,<br />
45º <br />
<br />
50º<br />
91-96<br />
SW 1 all 84º 45º 35º 45º 98-100<br />
SWH 1 all 84º 45º 35º 45º 98-101<br />
THD all<br />
45º 45º <br />
<br />
<br />
<br />
<br />
width ><br />
<br />
120, 123,<br />
165<br />
The information listed only applies<br />
to hangers manufactured by<br />
<strong>USP</strong> Structural <strong>Connectors</strong>® and<br />
installed according to the<br />
instructions listed in this catalogue.<br />
Some of the options listed may not<br />
have been evaluated on a single<br />
hanger. The designer must always<br />
evaluate each connection, including<br />
the joist and header capacities,<br />
before specifying a specialty<br />
connector. <strong>USP</strong> sloped hangers are<br />
manufactured with the plumb cut of<br />
the joist already calculated. If a<br />
hanger with a different height is<br />
needed, it must be specified at the<br />
time of ordering.<br />
Materials: Steel gauge may vary<br />
from that specified depending on<br />
the specialty option and<br />
manufacturing process used. Some<br />
formed hangers may be welded<br />
when modifying the hanger. Hanger<br />
configurations, fastener schedules,<br />
and height may vary from the tables<br />
depending on the joist size, skew,<br />
and slope.<br />
Finish: See specific hanger option<br />
tables. Welded hangers are painted<br />
with <strong>USP</strong> gray primer. Custom<br />
hangers available in Hot-dip<br />
galvanized, use HDG after product<br />
number.<br />
Factored Resistance: For multiple<br />
options for the same connector, use<br />
the most conservative reduction to<br />
give the lowest design load.<br />
Installation:<br />
• Fill all nail holes with fasteners<br />
specified in the tables.<br />
• Fastener quantities may increase<br />
from the amount listed in the tables<br />
depending on hanger option.<br />
• NA16D-RS and NA20D nails are<br />
supplied with hangers.<br />
• For type A skewed hangers, the<br />
end of joist must be bevel cut; for<br />
type B skewed hangers, the end of<br />
joist must be butt-cut.<br />
© Copyright 2013 <strong>USP</strong> Structural <strong>Connectors</strong> ®<br />
THDH all 45º 45º <br />
THF<br />
67-1/2º<br />
50º<br />
45º <br />
<br />
width ><br />
<br />
120,123,<br />
166-167<br />
118,<br />
121-122<br />
<br />
<br />
210<br />
1-800-328-5934 • www.<strong>USP</strong>connectors.com
Change language