Leonardo 250-300 Repair Manual 2004 - Wheels Academy

More documents

Recommendations

Info

LEONARDO 250 - 300 GENERAL INFORMATION 1.7. SPECIFICATIONS 1.7.1. SPECIFICATIONS Description 250 300 DIMENSIONS Max. length 1865 mm Max. length (rear mudguard extension included ) 1955 mm Max. width 770 mm Overall height (front part of the fairing included) 1410 mm Seat height 780 mm Distance between centres 1325 mm Min. ground clearance 135 mm Weight ready for starting 150 kg ENGINE Type One-cylinder, 4-stroke engine with overhead camshaft Number of valves 2 Number of cylinders 1 Total displacement 249,78 cm³ 264,47 cm³ Bore/stroke 69,0 mm / 66,8 mm 71,0 mm / 68,8 mm Compression ratio 10 ± 0,5 :1 Starting Elettric Engine idling rpm 1500 ± 100 rpm 1450 ± 100 rpm Clutch Automatic dry centrifugal Clutch gear Automatic Lubrication system Wet sump lubrication, forced circulation with mechanical pump; oil level check by means of a graduated dipstick Cooling system Liquid cooling, forced circulation with centrifugal pump TRASMISSION Speed change gear Automatic continuous Primary V-belt Secondary Gear Total engine / wheel ratio Minimun 15,808 Maximium 5,539 CAPACITA’ Fuel (reserve included) 9,5 l Fuel reserve 1,5 l Engine oil - engine oil change only 1200 cm³ - Engine oil and filter change ⎯ - Change for engine overhaul 1400 cm³ Transmission oil 250 cm Coolant 1,3 l (50% water + 50% antifreeze with ethylene glycol) Front fork oil 148 cm³ (for each rod) Seats 2 Vehicle max. load (rider + luggage) 105 kg Vehicle max. load (rider + passenger + luggage) 200 kg CARBURENTTOR Model TEI KEI 5 GM1A TK 5SE - alternative ⎯ Choke tube equivalent diameter 28 mm 28 mm Choke tube (Mikuni) ⎯ Choke tube (Keihin) ⎯ FUEL SUPPLY Type Fuel FRAME Type Vacuum pump Premium grade unleaded petrol, min. O.N. 91 (N.O.R.M.) and 81 (N.O.M.M.). One beam at the front, split in two overlapping cradles at the rear, in steel tubes with high yield point Steering inclination angle 28° Fore stroke 100 mm 1 - 15
GENERAL INFORMATION LEONARDO 250 - 300 SUSPENSIONS Front Stroke Rear Telescopic hydraulic fork 90 mm Two hydraulic shock absorbers with compression and rebound damping, spring preload adjustment 90 mm Wheel stroke BRAKES Front Rear combined WHEEL RIMS Type in light alloy Front 3,00 x 12’’ Rear 3,50 x 12’’ PNEUMATICI Disc brake - Ø 220 mm - with hydraulic transmission Disc brake - Ø 220 mm - with hydraulic transmission Type TUBELESS Front 130 / 70 - 12’’ 56 P - alternative 130 / 70 - 12’’ 56 P Rear 130 / 70 - 12’’ 62 L - alternative 130 / 70 - 12’’ 62 P Standard inflation pressure Front Rear 190 kPa (1,9 bar) 210 kPa (2,1 bar) Inflation pressure with passenger Front Rear 210 kPa (2,1 bar) 240 kPa (2,4 bar) IGNITION Type C.D.I. / inductive 4 AS-AP Spark advance Minimum 10° a 1500 rpm Maximum 32° a 5000 rpm SPARK PLUG Standard NGK - DR8EA Spark plug gap 0,6 - 0,7 mm ELECTRICAL SYSTEM Battery 12 V - 12Ah Fuses 20 - 15 - 7,5A Generator (with permanent magnet) 12V - 200 W BULBS Low / high beam 12 V - 35 / 35 W Front parking light 12 V - 3 W Direction indicators 12 V - 10 W Rear parking light / stop light 12 V - 5/21 W Number plate light 12 V – 5 W Dashboard lights 12 V - 1,2 W WARNING LIGHTS Direction indicators 12 V – 2 W Engine oil change 12 V – 2 W Low beam 12 V – 2 W High beam 12 V – 2 W Fuel reserve 12 V – 2 W Minimum 2° a 1500 rpm Maximum 22° a 8250 rpm 1 - 16
Page 1 and 2: 1194 4 00/2004-04 LEONARDO 250 - 30
Page 3 and 4: INTRODUCTION LEONARDO 250 - 300 CON
Page 5 and 6: INTRODUCTION LEONARDO 250 - 300 0.1
Page 7 and 8: INTRODUCTION LEONARDO 250 - 300 RIG
Page 9 and 10: GENERAL INFORMATION LEONARDO 250 -
Page 21: GENERAL INFORMATION LEONARDO 250 -
Page 31 and 32: PERIODIC MAINTENANCE LEONARDO 250 -
Page 55 and 56: LEONARDO 250 - 300 LUBRICATION LUBR
Page 57 and 58: LEONARDO 250 - 300 LUBRICATION 3.1.
Page 59 and 60: FUEL SYSTEM LEONARDO 250 - 300 CONT
Page 61 and 62: FUEL SYSTEM LEONARDO 250 - 300 TANK
Page 63 and 64: FUEL SYSTEM LEONARDO 250 - 300 4.1.
Page 65 and 66: FUEL SYSTEM LEONARDO 250 - 300 4.2.
Page 67 and 68: FUEL SYSTEM LEONARDO 250 - 300 Key:
Page 69 and 70: FUEL SYSTEM LEONARDO 250 - 300 •
Page 71 and 72: COOLING SYSTEM LEONARDO 250 - 300 C
Page 73 and 74:
COOLING SYSTEM LEONARDO 250 - 300 5
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
LEONARDO 250 - 300 ENGINE ENGINE 6
Page 81 and 82:
LEONARDO 250 - 300 ENGINE 6.1. EXHA
Page 83 and 84:
LEONARDO 250 - 300 ENGINE • Relea
Page 85 and 86:
LEONARDO 250 - 300 ENGINE • Disco
Page 87 and 88:
LEONARDO 250 - 300 ENGINE • Place
Page 89 and 90:
LEONARDO 250 - 300 ENGINE 6.2.2. RE
Page 91 and 92:
LEONARDO 250 - 300 ENGINE • Conne
Page 93 and 94:
LEONARDO 250 - 300 ENGINE • Refit
Page 95 and 96:
LEONARDO 250 - 300 ENGINE • Refit
Page 97 and 98:
CYCLE PARTS LEONARDO 250 - 300 CONT
Page 99 and 100:
CYCLE PARTS LEONARDO 250 - 300 7.1.
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
CYCLE PARTS LEONARDO 250 - 300 •
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
CYCLE PARTS LEONARDO 250 - 300 •
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
CYCLE PARTS LEONARDO 250 - 300 7.10
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
LEONARDO 250 - 300 ELECTRICAL SYSTE
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
show all

Leonardo 250-300 Repair Manual 2004 - Wheels Academy

Create successful ePaper yourself

Delete template?

Save as template?