Leonardo 250-300 Repair Manual 2004 - Wheels Academy

More documents

Recommendations

Info

LEONARDO 250 - 300 PERIODIC MAINTENANCE ENGINE OIL AND FILTER CHANGE • Place the motorcycle on firm and level ground. • Place the motorcycle on the centre stand. WARNING Allow the engine and exhaust system to cool down before proceeding. • Stop the engine and allow it to cool, before draining the oil in the crankcase, so that the oil itself is also cool. • Unscrew and remove the cap/dipstick (1). • Place a container under the engine oil filter. • Loosen and remove engine oil filter (2). WARNING Used oil contains substances that are harmful to the environment, even small quantities must be disposed of in compliance with the regulations in force. • Unscrew and remove the oil drain cap (3) and allow all the engine oil to drain out. • Fit a new oil filter (2). Take care to lubricate filter O- rings. • Refit and tighten the drain plug (3). • Refill through the engine oil filler hole with 1500 cc (91.5 cu in) of oil. • Refit and tighten the cap/dipstick (1). • Start the engine and allow it to run for a few minutes. Switch off and allow to cool. • Check the engine oil level. 2 - 19
PERIODIC MAINTENANCE LEONARDO 250 - 300 2.8. THE TRANSMISSION OIL 2.8.1. THE TRANSMISSION OIL CHECKING THE TRANSMISSION OIL LEVEL To check the transmission oil level, proceed as follows. • Drive for a few miles until the engine reaches the normal running temperature, then stop it. • Position the vehicle on the stand. • Put a graduated container with at least 100 cmC capacity under the drain plug (1). • Unscrew the filling cap (2) and the oil drain plug (1). • Let all the oil flow out of the oil pan, measure the quantity and if it is less than 90 cmC, top up by adding the lacking quantity. • Tighten the drain plug (1). • Inject the oil through the filling hole by means of a syringe or a similar system. IMPORTANT To facilitate the filling of the oil pan, rotate the wheel with your hands. • Screw and tighten the filling cap (2). CHANGING THE TRANSMISSION OIL To ensure vehicle good efficiency and durability, see 2.1.2 (PERIODIC MAINTENANCE CHART). • Drive for a few miles until the engine reaches the normal running temperature, then stop it. • Position the vehicle on the stand. • Put a graduated container with at least 100 cmC capacity under the drain plug (1). • Unscrew the filling cap (2) and the oil drain plug (1). • Let all the oil flow out of the oil pan. • Tighten the drain plug (1). • Pour 90 cmC of oil through the filling hole, by means of a syringe or a similar system. IMPORTANT To facilitate the filling of the oil pan, rotate the wheel with your hands. • Screw and tighten the filling cap (2). WARNING Tighten the filling cap and the drain plug thoroughly and make sure that there are no oil leaks. Periodically make sure that there are no leaks in correspondence with the oil pan cover seal. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would accelerate the wear of the moving parts and may also cause irreparable failures. 2 - 20
Page 1 and 2: 1194 4 00/2004-04 LEONARDO 250 - 30
Page 3 and 4: INTRODUCTION LEONARDO 250 - 300 CON
Page 5 and 6: INTRODUCTION LEONARDO 250 - 300 0.1
Page 7 and 8: INTRODUCTION LEONARDO 250 - 300 RIG
Page 9 and 10: GENERAL INFORMATION LEONARDO 250 -
Page 31 and 32: PERIODIC MAINTENANCE LEONARDO 250 -
Page 47: PERIODIC MAINTENANCE LEONARDO 250 -
Page 55 and 56: LEONARDO 250 - 300 LUBRICATION LUBR
Page 57 and 58: LEONARDO 250 - 300 LUBRICATION 3.1.
Page 59 and 60: FUEL SYSTEM LEONARDO 250 - 300 CONT
Page 61 and 62: FUEL SYSTEM LEONARDO 250 - 300 TANK
Page 63 and 64: FUEL SYSTEM LEONARDO 250 - 300 4.1.
Page 65 and 66: FUEL SYSTEM LEONARDO 250 - 300 4.2.
Page 67 and 68: FUEL SYSTEM LEONARDO 250 - 300 Key:
Page 69 and 70: FUEL SYSTEM LEONARDO 250 - 300 •
Page 71 and 72: COOLING SYSTEM LEONARDO 250 - 300 C
Page 73 and 74: COOLING SYSTEM LEONARDO 250 - 300 5
Page 79 and 80: LEONARDO 250 - 300 ENGINE ENGINE 6
Page 81 and 82: LEONARDO 250 - 300 ENGINE 6.1. EXHA
Page 83 and 84: LEONARDO 250 - 300 ENGINE • Relea
Page 85 and 86: LEONARDO 250 - 300 ENGINE • Disco
Page 87 and 88: LEONARDO 250 - 300 ENGINE • Place
Page 89 and 90: LEONARDO 250 - 300 ENGINE 6.2.2. RE
Page 91 and 92: LEONARDO 250 - 300 ENGINE • Conne
Page 93 and 94: LEONARDO 250 - 300 ENGINE • Refit
Page 95 and 96: LEONARDO 250 - 300 ENGINE • Refit
Page 97 and 98: CYCLE PARTS LEONARDO 250 - 300 CONT
Page 99 and 100:
CYCLE PARTS LEONARDO 250 - 300 7.1.
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
CYCLE PARTS LEONARDO 250 - 300 •
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
CYCLE PARTS LEONARDO 250 - 300 •
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
CYCLE PARTS LEONARDO 250 - 300 7.10
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
LEONARDO 250 - 300 ELECTRICAL SYSTE
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
show all

Leonardo 250-300 Repair Manual 2004 - Wheels Academy

Create successful ePaper yourself

Delete template?

Save as template?