S90 XS/S70 XS Reference Manual - zZounds.com
S90 XS/S70 XS Reference Manual - zZounds.com
S90 XS/S70 XS Reference Manual - zZounds.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Reference</strong><br />
Effect Parameters<br />
Switch<br />
This parameter is available only for the Master Effect.<br />
Category<br />
Type<br />
From the Category column, you can select one of the Effect Categories, each of which contains similar Effect types.<br />
From the Type column, you can select one of the Effect Types listed in the selected Category.<br />
Settings: Details about the Effect categories and the Effect types are described on page 16.<br />
NOTE: The “Category” is not edited in the Reverb and the Master effect parameter display because there is only one Reverb/Master<br />
category.<br />
Preset<br />
This lets you call up pre-programmed settings for each Effect type, designed to be used for specific applications and<br />
situations. You can change how the sound is affected by the selected pre-programmed settings.<br />
NOTE: For a list of the preset of each effect type, see the Data List (separate PDF documentation).<br />
Effect Parameter 1 – 16<br />
The effect parameter differs depending on the currently selected effect type. For details about the Effect parameters,<br />
refer to page 19. For a <strong>com</strong>plete list of the available Effect parameters for each Effect type, refer to the Effect Type List in<br />
the Data List (separate PDF documentation).<br />
5 Master EQ<br />
From this display you can apply five-band equalization to all parts<br />
of the selected Multi.<br />
Shape<br />
Enables you to select one of two equalizer shapes: shelving or<br />
peaking. This parameter is available for Low and High.<br />
Settings: shelv, peak<br />
shelv (Shelving type)<br />
This type of EQ shape lets you attenuate/boost the signal at<br />
frequencies above or below the specified Frequency setting.<br />
EQ Low<br />
EQ High<br />
+<br />
0<br />
–<br />
Gain<br />
Frequency<br />
Frequency<br />
+<br />
0<br />
–<br />
Frequency<br />
Gain<br />
Frequency<br />
Gain<br />
+<br />
0<br />
–<br />
Q (frequency bandwidth)<br />
5 bands Low Lo-Mid Mid Hi-Mid High<br />
Frequency<br />
peak (Peaking type)<br />
This type of EQ shape lets you attenuate/boost the<br />
signal at the specified Frequency setting.<br />
+<br />
0<br />
–<br />
Gain<br />
Frequency<br />
Frequency<br />
Basic Structure<br />
Voice<br />
Performance<br />
Multi<br />
SEQ Play<br />
Master<br />
Remote<br />
File<br />
Audio Rec/Play<br />
Utility<br />
Multi<br />
Play<br />
Mixing<br />
Edit Select<br />
Common Edit<br />
Name<br />
Arpeggio<br />
Controller<br />
Effect<br />
Parameter<br />
Master EQ<br />
A/D Out<br />
A/D FX<br />
Parameter<br />
Part Edit<br />
Voice<br />
Play Mode<br />
Arpeggio<br />
Arp Edit<br />
Arp 1-5 Type<br />
Filter/EG<br />
3 Band EQ<br />
Rcv Sw<br />
FX Send<br />
Job Select<br />
Recall<br />
Bulk<br />
Copy<br />
Initialize<br />
Freq (Frequency)<br />
Frequencies around this point are attenuated /boosted by the “Gain” setting below.<br />
Appendix<br />
Settings: <br />
When the Shape is set to “shelv”: 32Hz – 2.0kHz, When the Shape is set to “peak”: 63Hz – 2.0kHz<br />
Lo-Mid, Mid, Hi-Mid<br />
100Hz – 10.0kHz<br />
High<br />
500Hz – 16.0kHz<br />
Gain<br />
Determines the level gain for the Frequency (set above), or the amount the selected frequency band is attenuated or<br />
boosted.<br />
Settings: -12dB – +0dB – +12dB<br />
<strong>Reference</strong> <strong>Manual</strong><br />
97