STARTING GUIDE FRENIC-Eco . FRN-F1 - Welcome to Fuji Electric

More documents

Recommendations

Info

J codes: Application functions Code Name Data setting range Default setting Actual setting J01 PID control Mode selection 0: Disable 1: Enable (normal operation) 2: Enable (inverse operation) J02 Remote process command 0: Enable arrow keys on keypad 1: PID process command 1 3: Enable terminal command UP/DOWN control 4: Command via communications link J03 P (gain) 0.000 to 30.000 J04 J05 J06 J10 J11 J12 J13 I (integral time) 0.0 to 3600.0 s D (differential time) 0.00 to 600.00 s Feedback filter 0.0 to 900.0 s Anti reset windup 0 to 200 % Select alarm output (Refer to FRENIC-Eco user's manual) Upper limit alarm (AH) 0 to 100 % Lower limit alarm (AL) 0 to 100 % J15 Stop frequency for slow flowrate 0: Disable 1 to 120 Hz J16 Slow flowrate level stop latency 1 to 60 s J17 Starting frequency 0: Disable 1 to 120 Hz J18 Upper limit of PID process output 1 to 120 Hz 999: Depends on setting of F15 J19 Lower limit of PID process output 1 to 120 Hz 999: Depends on setting of F16 J21 Dew condensation prevention (Duty) 1 to 50 % J22 Commercial power switching sequence 0: Keep inverter operation (Stop due to alarm) 1: Automatically switch to commercial-power operation J23 Starting from the Slow Flowrate Stop (Feedback deviation level) 0 to 100 % J24 Starting from the Slow Flowrate Stop (Start latency) 0 to 60 s J25 Pump control Mode selection 0: Disable 1: Enable (Fixed inverter-driven motor) 2: Enable (Floating inverter-driven motor) J26 Motor 1 mode 0: Disable (Always OFF) 1: Enable J27 Motor 2 mode 2: Force to run by commercial power J28 J29 Motor 3 mode Motor 4 mode J30 Motor switching order 0: Fixed 1: Automatically (Constant run time) J31 Motor stop mode 0: Stop all motors (inverter-driven and commercial power-driven) 1: Stop inverter-driven motor only (excl. alarm state) 2: Stop inverter-driven motor only (incl. alarm state) J32 Periodic switching time for motor drive 0.0: Disable switching 0.1 to 720.0 h: Switching time range 999: Fix to 3 min J33 Periodic switching signaling period 0.00 to 600.00 s J34 Sequenced start of commercial power- Frequency 0 to 120 Hz driven motor 999: Depends on setting of J18 (This code is used to judge whether or not to start a commercial power-driven motor by checking the output frequency of the inverter-driven motor) J35 Duration 0.00 to 3600 s J36 Sequenced stop of commercial power- Frequency 0 to 120 Hz driven motor 999: Depends on setting of J19 (This code is used to judge whether or not to stop a commercial power-driven motor by checking the output frequency of the inverter-driven motor) J37 Duration 0.00 to 3600 s J38 J39 Contactor delay time 0.01 to 2.00 s Switching time for motor sequenced start (Deceleration time) 0.00: Depends on the setting of F08 0.01 to 3600 s Chapter 6: Function codes and application example 22 0 0 0.100 times 0.0 s 0.00 s 0.5 s 200 % 0 100 % 0 % 0 30 s 0 999 999 1 % 0 0 % 0 0 0 0 0 0 0 0 0.0 h 0.10 s 999 0.00 s 999 0.00 s 0.10 s 0.00 s
J40 J41 Code Name Data setting range Default setting Actual setting Switching time for motor sequenced stop (Acceleration time) 0.00: Depends on the setting of F07 0.01 to 3600 s 0.00 s Motor Unmount Switching Level 0 to 100 % 0 % J42 Switching motor sequenced start/sequenced stop (Dead 0.0: Disable band) 0.1 to 50.0 % J43 PID control startup frequency 0: Disable 1 to 120Hz 999: Depends on the setting of J36 J44 Motor Mount Switching Level 0: Depends on the setting of J41 1 to 100 % J45 Signal assignment to: [Y1 A/B/C] Selecting function code data assigns the corresponding function (for relay output card) to terminals [Y1A/B/C], [Y2A/B/C] and [Y3A/B/C] J46 [Y2 A/B/C] J47 J48 J49 J50 J51 J52 Cumulative run time of motor [Y3 A/B/C] Motor 0 Motor 1 Motor 2 Motor 3 Motor 4 J53 Maximum cumulative number of relay Y1 A/B/C to Y3 ON times A/B/C J54 [Y1], [Y2], [Y3] J55 J93 PID Start Frequency (Mount) J94 PID Start Frequency (Unmount) [Y5A/C], [30A/B/C] 100: Depends on the setting of E20 to E22 60 (1060): Sequenced start motor 1, inverter- (M1_I) driven 61 (1061): Sequenced start motor 1, commercial (M1_L) power-driven 62 (1062): Sequenced start motor 2, inverter- (M2_I) driven 63 (1063): Sequenced start motor 2, commercial (M2_L) power-driven 64 (1064): Sequenced start motor 3, inverter- (M3_I) driven 65 (1065): Sequenced start motor 3, commercial (M3_L) power-driven 67 (1067): Sequenced start motor 4, commercial (M4_L) power-driven 68 (1068): Periodic switching early warning (MCHG) 69 (1069): Pump control limit signal (MLIM) Indication of cumulative run time of motor for replacement Indication of maximum number of ON times of relay contacts on the relay output card or those built in inverter. Display of 1.000 means 1.000 times For relay output card For built-in mechanical contacts 0: Depends on the setting of J36 1 to 120 Hz 0: Depends on the setting of J34 1 to 120 Hz Chapter 6: Function codes and application example 23 0.0 % 999 0 % 100 100 100 --- --- --- --- --- --- --- --- 0 Hz 0 Hz
Page 1 and 2: STARTING GUIDE FRENIC-Eco . FRN-F1
Page 3 and 4: CONTENTS Chapter Page 1. SAFETY INF
Page 5 and 6: 1. SAFETY INFORMATION AND CONFORMIT
Page 7 and 8: 1.2 Conformity to European standard
Page 9 and 10: 3. ELECTRICAL INSTALLATION 3.1. Pow
Page 11 and 12: 3.4. Digital inputs (X1, X2, X3, X4
Page 13 and 14: 3.6 Setting up the slide switches S
Page 15 and 16: 5. QUICK START COMMISSIONING 5.1 In
Page 17 and 18: 6. FUNCTION CODES AND APPLICATION E
Page 19 and 20: E codes: Extension terminal functio
Page 21 and 22: Code Name Setting range Default set
Page 23 and 24: P codes: Motor parameters P01 Code
Page 25: Code Name Data setting range Defaul
Page 29 and 30: 6.2 Application examples 6.2.1 Line
Page 31 and 32: Timing scheme: ISW50 COMMERCIAL POW
Page 33 and 34: When setting J02 to 1, you have to
Page 35 and 36: 7. TROUBLESHOOTING Alarm code Alarm
Page 37 and 38: 8.2 IP54 specifications Output rati
Page 39 and 40: FRN37F1S-4 to FRN560F1S-4 Units exp
Page 41 and 42: 8.3.3 Keypad dimensions TP-E1 Units
Page 43 and 44: Drawing 4 Drawing 5 Drawing 6 DC Re
Page 45 and 46: FS5536 - 50 - 07 FS21312 - 78 - 07
Page 47 and 48: 9. OPTIONS 9.1 Options table Main o
Page 49: CONTACT INFORMATION Headquarters Eu

STARTING GUIDE FRENIC-Eco . FRN-F1 - Welcome to Fuji Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?