TAC Pneumatic Products Catalog

More documents

Recommendations

Info

AE-6xx, N100 Series Model Chart (Continued) Model No. Description AE-630-101 Subpanel for AE-629 and AE-630, 16 gage, perforated for #8 Type A sheet metal screws, flanged AE-631-101 Subpanel for AE-631, 16 gage, perforated for #8 Type A sheet metal screws, flanged Specifications Construction Dimensions W x H in. (mm) 14-1/2 x 20 (368 x 508) 22-1/2 x 28 (572 x 711) Doors Locking type, supplied with keys, rigidly supported. The doors are easily removed for protection on job site installation or mounting of components. Refer to Description Model Chart. Steel Gage Refer to Description Model Chart and N100-9901 Subpanels (T10) Model Chart. Knockouts Aligned so that a short nipple may be used to couple the panels. Refer to Description Model Chart. Appearance Refer to Description Model Chart. Locations NEMA Type 1. Mounting Four extruded mounting holes 1/4 in. (6mm). Dimensions Refer to Description Model Chart and N100-9901 Subpanels (T10) Model Chart. 6 © Copyright 2006 <strong>TAC</strong>. All Rights Reserved. F-27383-1
AK-42309- 00 Positive Positioning Relay Positive positioner pneumatic relay is used to accurately position an actuator stroke with respect to signal pressure from the controller. It can also be used to change the effective spring range of an actuator and increase the capacity of a controller. Features: For accurate positioning of valve and damper actuators, this positioner utilizes a pilot-operated, relay-type position-sensing mechanism, much more sensitive to actuator position changes than some competitive “force-balance” positioners. Model Chart Model No. Description AK-42309-500 a Specifications Positive Positioning Relay with Mounting Linkage. AK-42309-500 a AK-42309-500 positive positioner cannot be used with M556, M572, M573, M574, and MK-12000 Series actuators. Use N800-0555 positioner with M556, M573, and M574. Action Direct (increase in output pressure to actuator with an increase in pilot pressure from controller). Pilot input 0 to main air pressure, psig. Output Construction 0 to main air pressure, psig. Housing Polysulfone. Diaphragm Neoprene. Start point Adjustable 1 to 12 psig (7 to 83 kPa). Span Adjustable 2 to 13 psi (14 to 90 kPa); factory set at 5 psig. Stroke Adjustable 2 to 13 psi (14 to 90 kPa); factory set at 5 psig with feedback spring for 7/16 to 5 in. stroke. Supply air pressure Clean, oil free, dry air required (refer. EN-123). Maximum 30 psig (207 kPa). Nominal supply Environment 15 to 20 psig (103 to 138 kPa). Ambient temperature limits Shipping: -40 to 160�F (-40 to 71�C). Operating: 32 to 140�F (0 to 60�C). Humidity 5 to 95% R.H., non-condensing. Locations NEMA Type 1. Air connection code Air connections Refer to Figure 1. “M” and “B” Barbed for 1/4 in. O.D. plastic tubing. “P” Dual-contoured for 1/4 in. O.D. and 5/32 in. O.D. tubing. Air consumption for sizing air compressor 19 scim(5.2 mL/s) at 20 psig (138 kPa) supply. Air capacity for sizing air mains 20 scim (5.5 mL/s). Flow capacity 860 scim (235 mL/s) at 20 psig (138 kPa) supply. All necessary linkage provided to assemble AK-42309-500 to MK-2690-0-0-1 actuator and the Mounting linkage following actuator series; MK-3000, MK-4400, MK-4600-0-01, MK-4700, MK-4800, MK-6600, MK-6800, MK-6900, MK-7100, MK-8800 and MK-8900. Dimensions 2-1/2 H x 4-1/2 W x 3 D in. (64 x 114 x 76 mm). F-27383-1 © Copyright 2006 <strong>TAC</strong>. All Rights Reserved. 7
Page 1: TAC Pneumatic Products Catalog
Page 4 and 5: ii © Copyright 2006 TAC. All Right
Page 6 and 7: iv © Copyright 2006 TAC. All Right
Page 8 and 9: Mounting Post .....................
Page 10 and 11: Model Number Index Model Page Model
Page 16 and 17: A25x Series Receiver Gauges Receive
Page 18 and 19: A25x Series Typical Applications Br
Page 22 and 23: AK-42309-500 Accessories Model No.
Page 24 and 25: AK-52101 Typical Applications HKS-8
Page 26 and 27: AKR-40605 Accessories Model No. Des
Page 28 and 29: AKS-1100 Accessory Scale Plates (mu
Page 30 and 31: AL-15x Series Typical Applications
Page 32 and 33: AL-161-4 Typical Applications L1 L2
Page 34 and 35: AL-17x Series, AL-18x Series Typica
Page 36 and 37: AL-19x Series Typical Applications
Page 38 and 39: AL-7xxx Series Unit Ventilator Sub-
Page 40 and 41: C Series, CT Series (21 and 22 Seri
Page 46 and 47: H18-301 (2230-018) Room Humidistat
Page 48 and 49: H53-301 (2232-053) Room Humidity Tr
Page 50 and 51: H150-100 (2232-150) Duct Relative H
Page 52 and 53: HKS-2033, HKS-5033 Room/Duct Humidi
Page 54 and 55: HKS-8065 HKS-8065 Duct Enthalpy Tra
Page 56 and 57: M556 Series (2466 Series), M572 Ser
Page 62 and 63: MK-3xxx Series, MK4-3xxx Series Pne
Page 64 and 65: MK-3xxx Series, MK4-3xxx Series Acc
Page 66 and 67: MK-44xx Series, MK4-44xx Series Spe
Page 68 and 69: MK-46xx Series, MK4-46xx Series Acc
Page 70 and 71:
MK-6xxx Series Accessories Model No
Page 72 and 73:
MK-71xx Series, MK4-71xx Specificat
Page 74 and 75:
MK-7821, MK-7921 Specifications Con
Page 76 and 77:
MK-121xx Series Damper Actuators, P
Page 78 and 79:
N100-25xx Series Pneumatic Limit Co
Page 80 and 81:
N100-4017 (2364-202) Low Differenti
Page 82 and 83:
N800-0555 Series Model Chart (Conti
Page 84 and 85:
P323 Series (2323-5xx Series) Diffe
Page 86 and 87:
P541 Series (2341-5xx Series) TAC P
Page 88 and 89:
P541 Series (2341-5xx Series) Typic
Page 90 and 91:
PC-1xx Series Electrical Ratings. M
Page 92 and 93:
PKSR-9001, PKSR-9002 Accessories Mo
Page 94 and 95:
R432 Series (2372 Series) Typical A
Page 96 and 97:
R435 (2374-401) Typical Application
Page 98 and 99:
R436 Typical Applications 84 Diaphr
Page 100 and 101:
R, 2 R47 4-200 2 es) Ser R471, R472
Page 102 and 103:
R500 2351- 001) R500 (2351-001) TAC
Page 104 and 105:
R503 Series (2353-5xx Series) TAC P
Page 106 and 107:
R504 Series (2354 Series) TAC PNEUM
Page 108 and 109:
R516 (2360-501) TAC PNEUMODULAR �
Page 110 and 111:
R527 Series, R528 Series (2368-5xx
Page 112 and 113:
R532 Series (2372 Series) TAC PNEUM
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
RKS-1001, RKS-2001, RKS-3002, RKS-4
Page 126 and 127:
RKS-1001, RKS-2001, RKS-3002, RKS-4
Page 128 and 129:
S510, S511 Series (2390 Series) Spe
Page 130 and 131:
S52x Series, S53x Series, S54x Seri
Page 132 and 133:
S52x Series, S53x Series, S54x Seri
Page 134 and 135:
T12 through T33 Series (2211 throug
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
T34-3011 (2218-301, 2218-534 Kit) S
Page 142 and 143:
T35-301, T36-301 (2212-318, 2212-31
Page 144 and 145:
T53-101 (2220-053) Accessories Mode
Page 146 and 147:
T150 Series (2252 Series) Model Cha
Page 148 and 149:
T460 Series (2298 Series) Unit Temp
Page 150 and 151:
TK-1xxx Series, TKR-1xxx Series Sin
Page 152 and 153:
TK-1xxx Series, TKR-1xxx Series F -
Page 154 and 155:
TK-1071 Series, TK-1171 Submaster R
Page 156 and 157:
TK-17xx Series Dual Setpoint, Singl
Page 158 and 159:
TK-17xx Series Specifications (Cont
Page 160 and 161:
TK-18xx Series, TKR-18xx Series Fig
Page 162 and 163:
TK-2xxx Series, TK-3xxx Series, TK-
Page 164 and 165:
TK-6xxx Series, TK-8xxx Series Rela
Page 166 and 167:
TK-9xxx Series Relay Bulb Thermosta
Page 168 and 169:
TKS-5001, TKS-5001-600, TKS-6001 Ro
Page 170 and 171:
TS-29x Series Dial Thermometers Dia
Page 172 and 173:
Accessories Application 2 X 2 Therm
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Accessories Application Adapts exis
Page 180 and 181:
Accessories Application Ball joint
Page 182 and 183:
Accessories Application Damper actu
Page 184 and 185:
Accessories Application 3/4 in. MNP
Page 186 and 187:
Accessories Application Room thermo
Page 188 and 189:
Page 190 and 191:
Accessories This thermostat convers
Page 192 and 193:
Accessories Illustration Model No.
Page 194 and 195:
Accessories Illustration Model No.
Page 196 and 197:
TAC PNEUMODULAR Accessories TAC PNE
Page 198 and 199:
TAC PNEUMODULAR Accessories Illustr
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Tools 190 Illustration Model No. De
Page 206:
Tools 192 © Copyright 2006 TAC. Al
show all

TAC Pneumatic Products Catalog

Create successful ePaper yourself

Delete template?

Save as template?