ToneLab SE Owner's manual - Vox
ToneLab SE Owner's manual - Vox
ToneLab SE Owner's manual - Vox
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
CONTROL pedal: ROT SPD:<br />
If you select “ROT SPD” as the CONTROL pedal<br />
setting, the rotation speed will alternate between<br />
SLOW/FAST (SPEED 1/SPEED 2) each time<br />
you press the CONTROL pedal switch. This lets<br />
you control the effect just as on an actual rotary<br />
speaker. (p.56 Control pedal settings)<br />
8. PITCH SHIFTER (PITCH) MONO IN/MONO OUT 1<br />
This is a pitch shifter with a range of two octaves up or down, rivaling sophisticated<br />
rack-mounted signal processors.<br />
PITCH SHIFTER TIPS: If you assign the PITCH knob to an expression pedal,<br />
you can use the pedal to control the pitch change. (p.53 Using the expression<br />
pedal to control the sound)<br />
[1] “PITCH” –24–+24 * Adjusts the pitch in 100-cent units.<br />
[2] “FINE” –50–+50 * Adjusts the pitch in one-cent units.<br />
[4] “TRACKING” 10–150 [ms] Adjusts the tracking of the pitch shifter (i.e., how<br />
closely it will follow). Shorter settings are effective if<br />
the PITCH setting is close to 0, and longer settings<br />
are effective if the PITCH setting is close to +/–24.<br />
While listening to the pitch-shifted sound, adjust<br />
this so that you do not have difficulty playing.<br />
[5] “DIRECT” 0.0–10.0 * Adjusts the level of the direct sound.<br />
[6] “EFFECT” 0.0–10.0 * Adjusts the level of the effect sound.<br />
9. MOD DELAY (MOD DLY) MONO IN/MONO OUT 1 (MODE=1)<br />
MONO IN/MONO OUT 3 (MODE=2) MONO IN/STEREO OUT 1 (MODE=3)<br />
This models an analog delay that lets you add a vibrato effect to the delayed<br />
sound. The actual unit provided 400 ms of delay time, but this simulation extends<br />
this up to 1400 ms while maintaining the same warm sound, and can also be used<br />
as a sub-delay for the DELAY section. The CHORUS/VIBRATO switch of the original<br />
unit has been replaced by a knob with a range of 0.1–10 Hz, giving you even<br />
more versatility than the original.<br />
[1] “SPEED” 0.100–10.00 [Hz] * Adjusts the modulation speed.<br />
[2] “DEPTH” 0.0–10.0 * Adjusts the modulation depth.<br />
[3] “FEEDBACK” 0.0–10.0 * Adjusts the amount of feedback.<br />
[4] “TIME” 1.0–10.0 * Specifies the delay time.<br />
[5] “MODE” 1,2,3 Selects the output method.<br />
1: Mono output.<br />
2: Stereo mode with effect sound from the<br />
right and dry sound from the left.<br />
3: Reverse-phase stereo mode with dry +<br />
effect in the left side and dry - effect in the<br />
right side.<br />
[6] “MIX” 0.0–10.0 * Adjusts the mix amount of the effect sound.<br />
REVERB DELAY MODULATION PEDAL CABINET AMP TYPE Amp/Effect<br />
TYPE<br />
43