ToneLab SE Owner's manual - Vox

More documents

Recommendations

Info

5. Slowly advance the expression pedal 1 away from yourself (pedal forward), and take your hand off the pedal when it stops. NOTE: If you decide to cancel the calibration procedure, press the EXIT button. 6. Press the GLOBAL button. The name display will indicate COMPLETE for one second, and then ToneLabSE will return to normal operation. If the sensitivity could not be adjusted correctly, the name display will indicate ERROR, and will then indicate EXP1 MIN. Repeat the procedure from step 3. NOTE: If you are still unable to adjust the sensitivity after repeated attempts, it is possible that ToneLabSE has malfunctioned. Please contact your dealer or Vox authorized service center. EXPRESSION PEDAL 2 1. Turn the power OFF. 2. While holding down the CONTROL button and the CHAIN button, turn the power on. The name display indicates EXP2 MIN. Perform steps 3–6 as described above to adjust the sensitivity of expression pedal 2. NOTE: If you are still unable to adjust the sensitivity after repeated attempts, it is possible that ToneLabSE has malfunctioned. Please contact your dealer or Vox authorized service center. 58
Control via MIDI MIDI stands for Musical Instrument Digital Interface, and is a world-wide standard for exchanging various types of musical data between electronic musical instruments and computers. When MIDI cables are used to connect two or more MIDI devices, performance data can be exchanged between the devices, even if they were made by different manufacturers. ToneLabSE can use MIDI to communicate in the following ways with another MIDI device. You can: • Operate ToneLabSE to switch programs on an external MIDI device, or switch ToneLabSE programs from an external MIDI device. →“Program change” • Operate a connected optional foot controller to control an external MIDI device, or use an external MIDI device to control ToneLabSE’s volume or effects. →“Control change” • Use Sound Editor to edit parameters. →“Parameter change” • Backup (save) and restore (load) ToneLabSE program data. →“Backing up and restoring program data” NOTE: In order to do the above things, you need to use a MIDI cable to connect ToneLabSE and your external MIDI device, and set the MIDI channels appropriately. →“Connecting a MIDI device or computer,” “Setting the MIDI channel” NOTE: When you change the settings described in this section, they will be saved automatically. When you have finished making settings, simply press the EXIT switch (3.7) to return to the mode you were in. NOTE: If your external MIDI device does not recognize certain types of MIDI message, those messages cannot be used for control. Check the “MIDI implementation chart” of ToneLabSE and of your external MIDI device. CONNECTING A MIDI DEVICE OR COMPUTER If you want to control an external MIDI device from ToneLabSE, connect a MIDI cable from ToneLabSE’s MIDI OUT jack to the MIDI IN jack of your external MIDI device. If you want to control ToneLabSE from a MIDI sequencer or other external MIDI device, connect a MIDI cable from your external MIDI device’s MIDI OUT jack to ToneLabSE’s MIDI IN jack. When you connect ToneLabSE with a MIDI sequencer or sound editor, data will normally be sent in both directions, so you will need to connect MIDI cables from ToneLabSE’s MIDI OUT jack to the external MIDI device’s MIDI IN jack, and from the external MIDI device’s MIDI OUT jack to ToneLabSE’s MIDI IN jack. MIDI IN MIDI OUT MIDI interface MIDI OUT MIDI IN To a MIDI sequencer/computer NOTE: You will need a MIDI interface in order to connect your computer with ToneLabSE. Some USB-MIDI interface devices may not be able to transmit/receive the ToneLabSE’s MIDI exclusive messages. Tuner Pedals MIDI/DIGITAL Factory settings Troubleshooting Spec. Program List ToneLabSE 59
Page 1 and 2:
Owner's Manual E 1
Page 3 and 4:
CE mark for European Harmonized Sta
Page 5 and 6:
▼ buttons to select “Ln” (LIN
Page 7 and 8:
15. ToneLabSE provides a PEDAL effe
Page 9 and 10:
Program Select mode ...............
Page 11 and 12:
Introduction WELCOME ABOARD! Many t
Page 13 and 14:
Apart from the vital valve tone thi
Page 15 and 16:
A Guitarist’s Guided Panel Tour H
Page 17 and 18: 2 1.9 REVERB selector This selects
Page 19 and 20: 3.8 Name display Displays program n
Page 21: REAR PANEL 10 11 POWER SUPPLY 10.1
Page 24 and 25: MIC1 -10dBV MIC GAIN U 10 60 +10dB
Page 26 and 27: Playing ToneLabSE PROGRAM SELECT MO
Page 28 and 29: ACTIVATING OR DEACTIVATING THE KEY
Page 30 and 31: 6. Use the CABINET model selector t
Page 32 and 33: STORING A PROGRAM When your tweakin
Page 34 and 35: model. This time though, the “neu
Page 36 and 37: no feedback” emulation whenever A
Page 38 and 39: Original’s valve compliment: 5 x
Page 40 and 41: emains focused and well defined at
Page 42 and 43: B. CABINET MODELS Now let’s look
Page 44 and 45: It is renowned for its deep bass an
Page 46 and 47: [1] “SENS” 1.0...10.0 Adjusts t
Page 48 and 49: WARNING! Like all pedals of this ty
Page 50 and 51: 1. CLASSIC CHORUS (CL CHORUS) MONO
Page 52 and 53: [5] “MODE” S1, S2, P1, P2, P3 6
Page 54 and 55: 10. FILTRON STEREO IN/STEREO OUT 2
Page 56 and 57: 2. MULTI HEAD (MULTI HD) MONO IN/MO
Page 58 and 59: 10. HOLD DELAY (HOLD DLY) MONO IN/M
Page 60 and 61: 11. GATE MONO IN/STEREO OUT 1 This
Page 62 and 63: CALIBRATING THE TUNER When you swit
Page 64 and 65: SETTING THE EXPRESSION TARGET Here
Page 66 and 67: “EXP1INIT” lets you specify whe
Page 70 and 71: SETTING THE MIDI CHANNEL (GLOBAL
Page 72 and 73: 1. Press the GLOBAL button (3.4). 2
Page 74 and 75: Restoring the Factory Preset Progra
Page 76 and 77: 4. You’re using the ACOUSTIC peda
Page 78 and 79: Program list NAME PEDAL Ach-AMP Ach
Page 80 and 81: TOP PANEL: 1.2 1.4 5 1.5 1.3 1.6 1.
Page 82: Owner's Manual E 1 2003 VOX AMPLIFI
show all

ToneLab SE Owner's manual - Vox

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?