ToneLab SE Owner's manual - Vox

More documents

Recommendations

Info

CALIBRATING THE TUNER When you switch ToneLabSE on, the built-in tuner is automatically calibrated to A=440 Hz (a.k.a. “concert pitch”). If desired, you can recalibrate the tuner in the range of A = 438 Hz–445 Hz. • While the tuner is active, the value display (3.10) shows the frequency of the reference pitch. You can use the ▲, ▼ buttons to adjust (calibrate) this in the range of 438 Hz–445 Hz. NOTE: If you’ve recalibrated the tuner, remember that the setting will be automatically reset to 440 Hz the next time you turn ToneLabSE on. 52
Using the expression pedals EXPRESSION PEDAL SETTINGS ToneLabSE provides two expression pedals that you can use to control not only wah or volume, but a wide variety of effect parameters. For each program, you can specify which effect will be controlled, and how. HINT: If you’ve assigned a parameter to an expression pedal, operating the pedal has the same result as using the knob to edit the program. This means that when you operate the pedal, the EDIT icon will light. When you write the program, it will be written with the sound as currently specified by the position of the pedal. However if the expression target is “--OFF--,” “VOLUME,” “M/PITCH,” “D/INPUT,” or “R/ INPUT,” the program will not be edited by the pedal. EXPRESSION TARGET QUICK ASSIGN Here’s a very easy and convenient way to set the expression target. As an example, use the MODULATION selector to choose PITCH SHIFTER. So that the effect will be easy to hear, we’ll initialize the PITCH SHIFTER. If PITCH SHIFTER is already selected, turn the selector to choose a different effect, and then re-select PITCH SHIFTER. 1. When you’re editing PITCH SHIFTER, turn value knob 1 or use the √, ® buttons to make the name display show PITCH; the EXPRESSION button will light. If in this state you press and hold (for one second) the EXPRESSION button, the name display will indicate COMPLETE. The PITCH parameter has now been assigned to expression pedal 1, letting you control the amount of PITCH SHIFT. If you want to make more detailed settings, you can press the EXPRESSION button and set the minimum value (“EXP1 MIN,” value knob 2) and maximum value (“EXP1 MAX,” value knob 3) of the target range. In the same way, whenever the EXPRESSION button is lit during editing, you can press and hold the CONTROL button for one second to assign expression pedal 2 to control the parameter that is currently shown in the name display. NOTE: If you change the effect type of a parameter that is assigned to an expression target (i.e., to be controlled by one of the expression pedals), the target will be initialized to a setting of “--OFF--”. (However, “A/*****”, “D/INPUT”, and “R/INPUT” are exceptions.) HINT: If you’ve set the PEDAL effect type to “VOX WAH,” the “P/MANUAL” (wah position) will automatically be assigned to expression 1. If you then set the PEDAL effect to a different type without making any further settings, the Target, Min, and Max settings will automatically return to their former settings. (However in the case of “P/******”, it will be initialized to “--OFF--” instead of returning to its former setting.) NOTE: When you change the expression target, the MIN and MAX values will be initialized. Tuner Pedals MIDI/DIGITAL Factory settings Troubleshooting Spec. Program List 53
Page 1 and 2:
Owner's Manual E 1
Page 3 and 4:
CE mark for European Harmonized Sta
Page 5 and 6:
▼ buttons to select “Ln” (LIN
Page 7 and 8:
15. ToneLabSE provides a PEDAL effe
Page 9 and 10:
Program Select mode ...............
Page 11 and 12: Introduction WELCOME ABOARD! Many t
Page 13 and 14: Apart from the vital valve tone thi
Page 15 and 16: A Guitarist’s Guided Panel Tour H
Page 17 and 18: 2 1.9 REVERB selector This selects
Page 19 and 20: 3.8 Name display Displays program n
Page 21: REAR PANEL 10 11 POWER SUPPLY 10.1
Page 24 and 25: MIC1 -10dBV MIC GAIN U 10 60 +10dB
Page 26 and 27: Playing ToneLabSE PROGRAM SELECT MO
Page 28 and 29: ACTIVATING OR DEACTIVATING THE KEY
Page 30 and 31: 6. Use the CABINET model selector t
Page 32 and 33: STORING A PROGRAM When your tweakin
Page 34 and 35: model. This time though, the “neu
Page 36 and 37: no feedback” emulation whenever A
Page 38 and 39: Original’s valve compliment: 5 x
Page 40 and 41: emains focused and well defined at
Page 42 and 43: B. CABINET MODELS Now let’s look
Page 44 and 45: It is renowned for its deep bass an
Page 46 and 47: [1] “SENS” 1.0...10.0 Adjusts t
Page 48 and 49: WARNING! Like all pedals of this ty
Page 50 and 51: 1. CLASSIC CHORUS (CL CHORUS) MONO
Page 52 and 53: [5] “MODE” S1, S2, P1, P2, P3 6
Page 54 and 55: 10. FILTRON STEREO IN/STEREO OUT 2
Page 56 and 57: 2. MULTI HEAD (MULTI HD) MONO IN/MO
Page 58 and 59: 10. HOLD DELAY (HOLD DLY) MONO IN/M
Page 60 and 61: 11. GATE MONO IN/STEREO OUT 1 This
Page 64 and 65: SETTING THE EXPRESSION TARGET Here
Page 66 and 67: “EXP1INIT” lets you specify whe
Page 68 and 69: 5. Slowly advance the expression pe
Page 70 and 71: SETTING THE MIDI CHANNEL (GLOBAL
Page 72 and 73: 1. Press the GLOBAL button (3.4). 2
Page 74 and 75: Restoring the Factory Preset Progra
Page 76 and 77: 4. You’re using the ACOUSTIC peda
Page 78 and 79: Program list NAME PEDAL Ach-AMP Ach
Page 80 and 81: TOP PANEL: 1.2 1.4 5 1.5 1.3 1.6 1.
Page 82: Owner's Manual E 1 2003 VOX AMPLIFI
show all

ToneLab SE Owner's manual - Vox

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?