scsi interface specification - Plasmon

More documents

Recommendations

Info

DRIVE COMMAND SET READ SECTOR LOCATION (E6H)If the sector location being asked for is beyond the access range of the LaserDrive a CHECK CONDITIONstatus will be returned. The Request Sense data will indicate invalid LBA.If the location being asked for is valid, the LaserDrive will go to data in phase and return information aboutthe sector location in the Sector Location Page format as indicated in Table 36.Table 36. Sector Location PageBITBYTE7 6 5 4 3 2 1 000 LBA MSB01 LBA Next Byte02 LBA Next Byte03 LBA LSB04 PBA MSB05 PBA Next Byte06 PBA Next Byte07 PBA LSB08 Track MSB09 Track LSB10 Reserved11 Sector12 Media Side (0 - A; 1 - B)13 Media Zone (0 - inner; 1 - outer)14 - 21 ReservedPLASMON L M S - LD 6100/LF 6600/LF 6602 SCSI INTERFACE SPECIFICATIONPage 94
DRIVE COMMAND SETRELEASE (17H)RELEASE (17H)The RELEASE command is used to release previously reserved units.RELEASE Command (17H)BITBYTE7 6 5 4 3 2 1 000 RELEASE (17H)01 LUN 0 3rd Party Third Party Device ID Reserved02 Reserved03 Reserved04 Reserved05 ReservedThis command causes the LaserDrive to terminate any active reservation from the Initiator. It is not anerror for an Initiator to attempt to release a reservation that is not currently active. In this case, the drivereturns GOOD status.97653978 HPage 95
Page 1 and 2:
THE PLASMON INFINITYLD 6100 LASERDR
Page 3 and 4:
TABLE OF CONTENTSSCOPE 5RELATED PUB
Page 5 and 6:
SCOPESCOPEThis document describes t
Page 7 and 8:
GENERAL DESCRIPTIONGENERAL DESCRIPT
Page 9 and 10:
LASER-DRIVE SCSI CHARACTERISTICSCOM
Page 11 and 12:
LASER-DRIVE SCSI CHARACTERISTICSMES
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
SCSI COMMANDS AND STATUSCOMMAND IMP
Page 21 and 22:
SCSI COMMANDS AND STATUSCOMMAND DES
Page 23 and 24:
SCSI COMMANDS AND STATUSSTATUSSTATU
Page 25 and 26:
SCSI COMMANDS AND STATUSCOMMAND PRO
Page 27 and 28:
DRIVE COMMAND SETDRIVE COMMAND SETT
Page 29 and 30:
DRIVE COMMAND SETACCESS EVENT LOG (
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44: DRIVE COMMAND SETACCESS EVENT LOG (
Page 63 and 64: DRIVE COMMAND SETINQUIRY (12H)Table
Page 65 and 66: DRIVE COMMAND SETMEDIA SCAN (38H)ME
Page 67 and 68: DRIVE COMMAND SETMEDIA SCAN (38H)Th
Page 69 and 70: DRIVE COMMAND SETMODE SELECT (15H)T
Page 71 and 72: DRIVE COMMAND SETMODE SELECT (15H)T
Page 73 and 74: DRIVE COMMAND SETMODE SELECT (15H)W
Page 75 and 76: DRIVE COMMAND SETMODE SELECT (15H)S
Page 77 and 78: DRIVE COMMAND SETMODE SENSE (1AH)Al
Page 79 and 80: DRIVE COMMAND SETMODE SENSE (1AH)De
Page 81 and 82: DRIVE COMMAND SETMODE SENSE (1AH)LA
Page 83 and 84: DRIVE COMMAND SETMOVE MEDIA (02H -
Page 85 and 86: DRIVE COMMAND SETPREVENT/ALLOW MEDI
Page 87 and 88: DRIVE COMMAND SETREAD BUFFER (3CH -
Page 89 and 90: DRIVE COMMAND SETREAD DIAGNOSTIC LO
Page 91 and 92: DRIVE COMMAND SETREAD DIAGNOSTIC PH
Page 93: DRIVE COMMAND SETREAD SECTOR LOCATI
Page 97 and 98: DRIVE COMMAND SETREQUEST SENSE (03H
Page 111 and 112: DRIVE COMMAND SETRESERVE (16H)RESER
Page 113 and 114: DRIVE COMMAND SETSEEK (10 BYTE)SEEK
Page 115 and 116: DRIVE COMMAND SETSEND DIAGNOSTIC (1
Page 117 and 118: DRIVE COMMAND SETTEST UNIT READY (0
Page 119 and 120: DRIVE COMMAND SETWRITE (2AH - 10 BY
Page 121 and 122: DRIVE COMMAND SETWRITE AND VERIFY (
Page 123 and 124: DRIVE COMMAND SETWRITE BUFFER (3BH)
Page 129 and 130: GLOSSARYGLOSSARYThe glossary includ
Page 131 and 132: GLOSSARYLD 6100LEDLF 6600LF 6602Log
show all

scsi interface specification - Plasmon

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?