BaseStation 3200 User Manual - Baseline Systems

More documents

Recommendations

Info

C h a p t e r 1 – G e t t i n g S t a r t e dZone StatusNote that the status of each zone is shown inthe Zone Number list. The zone status codesare:OK – Working properlyOP – Open circuitSC – Short circuitER – Communication errorZone Numbers are Pre-Assigned in R-seriesAll conventional wire versions (R-series) of the 3200 have been pre-assigned at the factory suchthat terminal 1 is assigned to zone 1, terminal 2 is assigned to zone 2, etc. However, you canchange these zone numbers to organize Scheduling Groups, Primary and Linked zones to achieveoptimal watering behavior.To change or re-order zone numbers in an R-series unit, use the CLEAR function as outlinedabove, and then Assign each biCoder serial number to the desired Zone Number.The serial numbers for all terminals in 3200R controllers are shown on the label next to theterminals. The serial numbers for terminals in 5200R biCoders are shown on the door label.Assigning Other DevicesAir Temperature SensorsAn Air Temperature Sensor does not need to be assignedto any address, but it must be found by the controller.To search for an air temperature sensor, turn the dial tothe AUX position, choose Temp/Pause using theNEXT/PREV keys, and press ENTR. In the Pause Screen,select Search.If the air temperate sensor is found, it will show here.Pause DevicesPause Devices are assigned in the AUX dial position. For detailed instructions for Pause devices,refer to Pause biCoders in Section 3 below.Flow Meters and Flow SensorsFlow Meters and Flow Sensors are configured on the Flow Menu dial position. Refer to Flow inSection 3 below for detailed instructions for assigning and configuring Flow Meters and/or FlowSensors.Page 32Baseline 3200
C h a p t e r 1 – G e t t i n g S t a r t e dAssigning biSensors to Primary ZonesRefer to Section 2, Moisture Based Watering below for instructions to assign sensors to PrimaryZones.Setting the Controller Date and TimeTo set or change the controller date and time,turn the dial to the Date/Time menu, then usethe +/- and NEXT/PREV keys to set or changeeach field as desired.Warning: changing the date and time can causewatering events to be missed!Note that all menu screens on the 3200 includespecific help text to tell you what to do next.Auto Run Main ScreenThe Main Screen is shown while the dial is in theAuto Run position, and shows status for allelements of the 3200 controller.Air Temp: will show “None” if no air temperaturesensor connected to the system, otherwise willshow current air temperature.Remote: indicates the status of remotecommunications to the 3200. Possible indicatorsinclude:None: No remote communicationdevices were detected.Idle: One or more remote communication devices were detected, but none are in useat this time.BL Commander: A BL Commander remote control is currently active.BaseManager: BaseManager central control software is currently connected to andcommunicating with the controller.Two-wire: indicates the active electrical current on the Two-wire. This will indicate 0.00 Ampswhen two-wire is off,Flow: shows the real-time flow readings in GPM. If multiple flow sensors are connected to thesystem, this indicator will cycle through each flow sensor.Prog: Shows the status of all programs. The color indicator will cycle through the meaning ofeach color, and this is shown on the inside door label of the controller.MV: Shows the status of each master valve.Zone Status: Shows the status of each zone.Page 33Baseline 3200
Page 4 and 5: Table of ContentsIntroduction .....
Page 6 and 7: iSensor Menu ......................
Page 8 and 9: I n t r o d u c t i o nCabinet Opti
Page 10 and 11: Drier WetterI n t r o d u c t i o n
Page 12 and 13: I n t r o d u c t i o nOne importan
Page 14 and 15: I n t r o d u c t i o nAs you can s
Page 16 and 17: C h a p t e r 1 - G e t t i n g S t
Page 20 and 21: A1 2 3 4 5 6 7 8 9 10 11 12 B1 2 3
Page 38 and 39: C h a p t e r 2 - B a s i c P r o g
Page 46 and 47: C h a p t e r 3 - A d v a n c e d P
Page 55 and 56: C h a p t e r 4 - T r o u b l e s h
Page 57 and 58: C h a p t e r 5 - R e f e r e n c e
Page 80 and 81: A p p e n d i x - G l o s s a r y o
Page 82: Baseline Inc2700 E Lanark St, Ste 1

BaseStation 3200 User Manual - Baseline Systems

Create successful ePaper yourself

Delete template?

Save as template?