BaseStation 3200 User Manual - Baseline Systems

More documents

Recommendations

Info

C h a p t e r 5 – R e f e r e n c eSelf-Test – Verify and Repair AllThis function will verify communication with each of the devices on the two-wire. It does notcheck the valve current nor does it check biSensor readings. If it finds a problem, it will attemptto repair in the following repair order:Repair valve biCoder to zone number assignmentsRepair biSensor addressingRepair pause device addressingRepair air temperature sensor addressing If you are troubleshooting two-wire problems (damaged and repaired), it isa good idea to do a backup before doing search operations. Call Baselinesupport for help and guidelines, 866-294-5847.Manual Run ProgramThis dial position has three different operationsthat can be performed. The first menu item canbe toggled between the program start/stop andnext start date by using the + or – keys. Then use the NEXT/PREV keys to highlight the desiredprogram. Use the + or – key to then change the value for the highlighted program.1. A program that is stopped can be started (set to running). It will then run a full cyclewhen the dial is turned to Auto/Run.2. A program that is running can beterminated (set to stopped).3. A program that is using a Historical ETCalendar can have its next run dateset. Programs that do not use thismode have a fixed schedule and aremodified in the Day Intervals dialposition.Page 70Baseline 3200
C h a p t e r 5 – R e f e r e n c eManual WaterThis dial position provides a way to run a singlezone, the zones of a program, or all zones for aspecific amount of time. It is most often used for a system test or walk-around.The first menu item is used to set the operation for zones or programs. With the first fieldhighlighted, use the + or – key to toggle between Zones or zones of a program mode. Thefollowing values will control the watering behavior:Zone run time = the time that each zone will run (water). It can be set from 5 secondsto 6 hours. This is the time that each zone will run if multiple zones are specified.First zone delay = this is the time from when the dial is turned to the Auto/Runposition to when the first zone will actually start to water. This provides time to walkto the first zone to observe its behavior from start to finish. This time can be set from0 seconds to 10 minutes.Between Zone Delay = this is the delay time from one zone completing its run timeuntil the next zone is turned on. This time can be set from 0 seconds to 10 minutes.Manually Run Zone(s)With this mode selected in the first field, the second field or box is used to select the zone to run.Highlight this box by pressing the NEXT key one time (OFF is now highlighted). Here are theoptions for this field:Press the – key once to select ALL. This will run all of the zones in the controller insequential order.Press the + key to select the desired zone number. This will run a single zone.Use the + key to increment to the desired zone. Once the zone or all zones and times are set,turn the dial to Auto/Run to start the manual run operation.Run Zones of ProgramWith this mode selected in the first field, the second field or box is used to select the program torun. Highlight this box by pressing the NEXT key one time (OFF is now highlighted). Pressing the+ and – keys will scroll through the programs.Once the desired program is selected, and the times have been set. Turn the dial to Auto/Run tostart the manual run operation.Page 71Baseline 3200
Page 4 and 5:
Table of ContentsIntroduction .....
Page 6 and 7:
iSensor Menu ......................
Page 8 and 9:
I n t r o d u c t i o nCabinet Opti
Page 10 and 11:
Drier WetterI n t r o d u c t i o n
Page 12 and 13:
I n t r o d u c t i o nOne importan
Page 14 and 15:
I n t r o d u c t i o nAs you can s
Page 16 and 17:
C h a p t e r 1 - G e t t i n g S t
Page 18 and 19:
C h a p t e r 1 - G e t t i n g S t
Page 20 and 21:
A1 2 3 4 5 6 7 8 9 10 11 12 B1 2 3
Page 22 and 23: C h a p t e r 1 - G e t t i n g S t
Page 38 and 39: C h a p t e r 2 - B a s i c P r o g
Page 46 and 47: C h a p t e r 3 - A d v a n c e d P
Page 55 and 56: C h a p t e r 4 - T r o u b l e s h
Page 57 and 58: C h a p t e r 5 - R e f e r e n c e
Page 80 and 81: A p p e n d i x - G l o s s a r y o
Page 82: Baseline Inc2700 E Lanark St, Ste 1
show all

BaseStation 3200 User Manual - Baseline Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?