BaseStation 3200 User Manual - Baseline Systems

More documents

Recommendations

Info

C h a p t e r 5 – R e f e r e n c eEven DaysThis day interval mode will allow programs tostart on even days of the month.Odd DaysThis day interval mode will allow programs tostart on odd days of the month.Odd Days and Skip 31 stThis day interval mode will allow programs to start on odd days of the month, but will also notallow watering on the 31 st of the month, thus maintain a better every two day schedule whencrossing to a new month.Soak CyclePlease see a previous section for thisinformation. Refer to page 36, Using Soak cycles.MV/Pump StartThis dial position can be used to assign mastervalves to the corresponding mainline, and to alsoassign programs to the appropriate mainline.This screen shown to the right is nearly a duplicate of the mainline configure screen in the FlowMenu dial position. Normally closed master valves have a vale decoder assigned to them in thebiCoder menu dial position, and then they are assigned to a mainline in this screen. NormallyOpen Master Valves (shown in MV1 in this sample screen) are based on the flow device number(#1 in this case). For additional information, refer to page 48, Multiple Flow Devices andMainlines.Page 62Baseline 3200
C h a p t e r 5 – R e f e r e n c eDate/TimeThe date and time should be set when thecontroller is installed, and when it is poweredback up after being shut down for an extendedperiod of time. The real-time clock circuit is maintained for several days during a power outage,but will lose track of time after a week or more.Set the date by using NEXT/PREV to select the date field and then adjust the field value using the+ and – keys. When the desired date has been set, press the ENTR key, or just turn the dial to anew location to write the new date and time into the real-time clock electronics.Event DaysThe BaseStation 3200 supports eight event days.An event day will stop all watering, and will keepall programs from starting on that date. Anevent day can be scheduled up to a year in advance.To set a new event day, use NEXT/PREV to highlight an empty event day box and then use the +and – keys to set the desired date. Use the + and – keys to edit existing event days. An eventday may be cleared by pressing the CLR key when the day to be removed is highlighted.Page 63Baseline 3200
Page 4 and 5:
Table of ContentsIntroduction .....
Page 6 and 7:
iSensor Menu ......................
Page 8 and 9:
I n t r o d u c t i o nCabinet Opti
Page 10 and 11:
Drier WetterI n t r o d u c t i o n
Page 12 and 13: I n t r o d u c t i o nOne importan
Page 14 and 15: I n t r o d u c t i o nAs you can s
Page 16 and 17: C h a p t e r 1 - G e t t i n g S t
Page 20 and 21: A1 2 3 4 5 6 7 8 9 10 11 12 B1 2 3
Page 38 and 39: C h a p t e r 2 - B a s i c P r o g
Page 46 and 47: C h a p t e r 3 - A d v a n c e d P
Page 55 and 56: C h a p t e r 4 - T r o u b l e s h
Page 57 and 58: C h a p t e r 5 - R e f e r e n c e
Page 80 and 81: A p p e n d i x - G l o s s a r y o
Page 82: Baseline Inc2700 E Lanark St, Ste 1
show all

BaseStation 3200 User Manual - Baseline Systems

Create successful ePaper yourself

Delete template?

Save as template?