Printrex 980 Operator's Guide - TransAct

More documents

Recommendations

Info

Appendix B: Frequently Asked QuestionsImage Defect RecoverySamples of image defects that can be detected through test printing aredescribed below. When an image defect is found, carry out test printing todetermine the image defect type, and then perform an appropriate procedure.Vertical White Streak (Non-Discharge)This is a state in which ink drops cannot be discharged from Printhead nozzlesdue to dust, bubbles, thickened ink, wetting, etc. around Printhead nozzle.Page 116100-11672 - Rev D
Appendix A: Ordering Genuine Ithaca SuppliesFaint Image (Distortion)This is a state in which ink drops cannot be discharged from Printhead nozzlesdue to dust, bubbles, thickened ink, wetting, etc. around Printhead nozzle, or astate in which a condensed ink film is formed on the surfaces of Printheadnozzles, and as a result ink drops are not ejected.100-11672 - Rev D Page 117
Page 4:
This page intentionally left blankP
Page 8 and 9:
Paper Loading Procedure (Rear) ....
Page 10 and 11:
Slow To Print .....................
Page 12 and 13:
Page 14 and 15:
About Your Printrex ® 980 PrinterW
Page 16 and 17:
About Your Printrex ® 980 PrinterR
Page 18 and 19:
About Your Printrex ® 980 PrinterG
Page 20 and 21:
Page 22 and 23:
Power Supply and Power CordTo avoid
Page 24 and 25:
Do not place the printer close to d
Page 26 and 27:
Page 28 and 29:
Step-by-Step Installation Instructi
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77: Step-by-Step Installation Instructi
Page 101 and 102: Chapter 4Printrex ® 980 Specificat
Page 103 and 104: Printrex ® 980 Specifications and
Page 105: Printrex ® 980 Specifications and
Page 108 and 109: This page intentionally left blankP
Page 110 and 111: How to Operate the Printrex ® 980
Page 121 and 122: Chapter 6Troubleshooting100-11672 -
Page 123 and 124: Appendix A: Ordering Genuine Ithaca
Page 125: Appendix A: Ordering Genuine Ithaca
Page 177 and 178:
Appendix A: Ordering Genuine Ithaca
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295:
Appendix B: Frequently Asked Questi
show all

Printrex 980 Operator's Guide - TransAct

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?