Printrex 980 Operator's Guide - TransAct

More documents

Recommendations

Info

Appendix B: Frequently Asked QuestionsCode Detail Code Item Description24 01 Condition Climate Sensor is not connected.DetectedAction 1. Check Climate Sensor connection.2. Replace Climate Sensor.3. Replace Printer Controller PCB.25: Paper Suction Fan Error25 01 ConditionDetectedAction26: Power Supply Fan Error26 01 ConditionDetectedAction26 02 ConditionDetectedAction27: Cooling Fan Error27 01 ConditionDetectedAction29: Wipe Valve Error29 20 ConditionDetectedAction29 21 ConditionDetectedActionPaper Suction Fan is faulty or not connected.1. Check for a clogged fan.2. Check Suction Fan connector connection.3. Replace Suction Fan.4. Replace Printer Controller PCB.Power Supply Fan is faulty or not connected1. Check for a clogged fan.2. Check Power Supply Fan connectorconnection.3. Replace Power Supply Fan.4. Replace Printer Controller PCB.Power Supply Fan is faulty or not connected1. Check for a clogged fan.2. Check Power Supply Fan connectorconnection.3. Replace Power Supply Fan.4. Replace Printer Controller PCB.Power Supply Fan is faulty or not connected1. Check for a clogged fan.2. Check Power Supply Fan connectorconnection.3. Replace Power Supply Fan.4. Replace Printer Controller PCB.Wipe Valve position error1. Check Wipe Valve Sensor connectorconnection.2. Check Valve Motor connector connection.3. Replace Wipe Valve Sensor.4. Replace Valve Motor.5. Replace Valve Unit.Wipe Valve position error1. Check Valve Motor connector connection.2. Replace Valve Motor.Page 202100-11672 - Rev D
Appendix A: Ordering Genuine Ithaca SuppliesCode Detail Code Item Description3. Replace Valve Unit.29 22 Condition Wipe Valve position errorDetectedAction 1. Check Wipe Valve Sensor connectorconnection.2. Check Valve Motor connector connection.3. Replace Wipe Valve Sensor.4. Replace Valve Motor.5. Replace Valve Unit.29 23 Condition Wipe Valve position errorDetectedAction 1. Check Wipe Valve Sensor connectorconnection.2. Check Valve Motor connector connection.3. Replace Wipe Valve Sensor.4. Replace Valve Motor.5. Replace Valve Unit.29 7F Condition Wipe Valve position errorDetectedAction 1. Check Wipe Valve Sensor connectorconnection.2. Check Valve Motor connector connection.3. Replace Wipe Valve Sensor.4. Replace Valve Motor.5. Replace Valve Unit.1B: Printhead of the Fuse to Be Blown1B 01-FF(Additionalvalue ofK:01,C:02,M:04,Y:08)(MODULE1),(Additionalvalue ofK:10,C:20,M:40,Y:80)(MODULE2)F0: Software ErrorConditionDetectedActionF0 01 ConditionDetectedActionF0 02 ConditionDetectedActionPrinthead of the fuse to be blownReplace Printer Controller PCB.ASIC bus access timeout error1. Turn off Printer, and then turn on Printer2. Update the firmware.3. Save the printer stored data to a file, andthenreport to manufacturer.Command with invalid parameters sent to printprocessing Unit1. Turn off Printer, and then turn on Printer2. Update the firmware.100-11672 - Rev D Page 203
Page 4:
This page intentionally left blankP
Page 8 and 9:
Paper Loading Procedure (Rear) ....
Page 10 and 11:
Slow To Print .....................
Page 12 and 13:
Page 14 and 15:
About Your Printrex ® 980 PrinterW
Page 16 and 17:
About Your Printrex ® 980 PrinterR
Page 18 and 19:
About Your Printrex ® 980 PrinterG
Page 20 and 21:
Page 22 and 23:
Power Supply and Power CordTo avoid
Page 24 and 25:
Do not place the printer close to d
Page 26 and 27:
Page 28 and 29:
Step-by-Step Installation Instructi
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 101 and 102:
Chapter 4Printrex ® 980 Specificat
Page 103 and 104:
Printrex ® 980 Specifications and
Page 105:
Printrex ® 980 Specifications and
Page 108 and 109:
Page 110 and 111:
How to Operate the Printrex ® 980
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 121 and 122:
Chapter 6Troubleshooting100-11672 -
Page 123 and 124:
Appendix A: Ordering Genuine Ithaca
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162: Appendix A: Ordering Genuine Ithaca
Page 211: Appendix A: Ordering Genuine Ithaca
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295:
Appendix B: Frequently Asked Questi
show all

Printrex 980 Operator's Guide - TransAct

Create successful ePaper yourself

Delete template?

Save as template?