Printrex 980 Operator's Guide - TransAct

More documents

Recommendations

Info

Appendix B: Frequently Asked QuestionsWork at Printhead ReplacementHead Position Adjustment1) Adjust Head position. ("Head Position Adjustment" section)Work at Purge Unit ReplacementBlade Position Adjustment1) Loosen the screw by 1 turn.2) Set the key pins on holder of Blade with Blade Adjustment Tool.Set Blade Adjustment Tool in Print Module.Page 144100-11672 - Rev D
Appendix A: Ordering Genuine Ithaca Supplies3) Tighten the screw.4) Remove Blade Adjustment Tool.● Purge Unit Wipe Position Adjustment1) Enter "Rec wipe P number" that was noted before install the new Purge Unitto "Purge Unit wipe position" using service utility after turning Main PowerSwitch on. ("Consumable Parts Replacement Procedure" section.)Work at Transport Unit ReplacementPinch Roller Position Adjustment1) Print backfeed pattern. ("Backfeed Gap Adjustment"(page 5-92).)2) Observe the backfeed pattern and examine if Pinch Roller adjustment isnecessary according to the following. Perform the adjustment, if necessary.Examination Procedure:If the gray areas of backfeed pattern does not have difference in vertical lineand does not have overlap, adjustment is not necessary.If the second page shifts to right, shift the plate of Pinch Roller to "A" direction.If the second page shifts to left, shift the plate of Pinch Roller to "B" direction.Go to the section below.100-11672 - Rev D Page 145
Page 4:
This page intentionally left blankP
Page 8 and 9:
Paper Loading Procedure (Rear) ....
Page 10 and 11:
Slow To Print .....................
Page 12 and 13:
Page 14 and 15:
About Your Printrex ® 980 PrinterW
Page 16 and 17:
About Your Printrex ® 980 PrinterR
Page 18 and 19:
About Your Printrex ® 980 PrinterG
Page 20 and 21:
Page 22 and 23:
Power Supply and Power CordTo avoid
Page 24 and 25:
Do not place the printer close to d
Page 26 and 27:
Page 28 and 29:
Step-by-Step Installation Instructi
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 101 and 102:
Chapter 4Printrex ® 980 Specificat
Page 103 and 104: Printrex ® 980 Specifications and
Page 105: Printrex ® 980 Specifications and
Page 108 and 109: This page intentionally left blankP
Page 110 and 111: How to Operate the Printrex ® 980
Page 121 and 122: Chapter 6Troubleshooting100-11672 -
Page 123 and 124: Appendix A: Ordering Genuine Ithaca
Page 153: Appendix A: Ordering Genuine Ithaca
Page 205 and 206:
Appendix A: Ordering Genuine Ithaca
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295:
Appendix B: Frequently Asked Questi
show all

Printrex 980 Operator's Guide - TransAct

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?