Dolphin 9700 User's Guide Rev (a) - Finn-ID

More documents

Recommendations

Info

Communicating with the Dolphin TerminalTo initiate communications between the Dolphin terminal and peripheral, complete these steps:1. Insert the Dolphin terminal into the terminal well of the base.• The DOCK LED illuminates green. If the DOCK LED does not illuminate, make sure that the terminal isproperly seated. You may need to remove and re-insert the terminal.• The Dolphin terminal activates; if the power is off, the terminal automatically powers on. If the terminal doesnot power on, verify that the Honeywell power supply is properly connected to the cradle and plugged into afunctioning outlet.• If the base is connected to the workstation, the Dolphin terminal automatically opens ActiveSync to establisha connection.2. The base can now transfer data between the terminal and the host device. If communication doesnot occur, check the port connections to ensure that the cradle is correctly configured.Verifying CommunicationYou can verify that the USB driver is functioning by watching the COMM LED on the USB base. Whenthe COMM LED illuminates solid green, the base is communicating with the host device.Verifying Data TransferThe COMM LED flashes when data is being transferred via the base. For an RS232 connection, theCOMM LED flashes red and green. For a USB connection, the COMM LED flashes green.RS232 Communications CablesConnect the base to the host workstation or other device by plugging an RS232 serial cable into theRS232 Communications Port on the rear of the base. The wiring of your cable depends on whether theother device is set up as a Data Communications Equipment (DCE) or Data Terminal Equipment (DTE)device.The Communication Port is configured as a DCE device. To communicate with a DCE device, use eithera null modem adapter in line with a standard RS232 cable, or a null-modem serial cable. To communicatewith a DTE device such as a workstation, use a standard (or straight-through) RS232 cable.You can make your own cables by following the pin configuration in the chart below. To do so, you mustdetermine if your host RS232 device is 9-pin or 25-pin, and whether it is configured as a DCE or DTEdevice.12 - 8
RS232 Pin ConfigurationBase /Host Port(DCE)IBM AT DB9(DTE)IBM XT DB25(DTE)Modem DB25(DCE)Pin / Input Signal2 / (RD) 2 3 23 / (TD) 3 2 35 / (SG) 5 7 74 / (DTR) 4 20 66 / (DSR) 6 6 207 / (RTS) 7 4 58 / (CTS) 8 5 4Note: This base cannot be daisy-chained.MountingSet the base on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be sureto provide enough workspace with good lighting for the user to view and operate the Dolphin terminalwhile it is in the base.When choosing a location, bear in mind that:• the mounting location must allow users easy access to the Auxiliary Battery Well, and• the serial and USB ports as well as the power jack face straight out of the rear panel, and you will mostlikely want easy access to them in the future.Installation HardwareScrew:Washer:Nut:3/16 in. dia x 5/8 in. long pan head screw1/2 in. OD x 7/32 in. ID x 3/64 in. thick3/16 in. dia12 - 9
Page 1 and 2:
Dolphin ® 9700 Mobile Computerswit
Page 3 and 4:
Table of ContentsChapter 1 - Agency
Page 5 and 6:
System Menu........................
Page 7 and 8:
Communicating with the Dolphin Term
Page 9 and 10:
1Agency InformationDolphin 9700 mob
Page 11 and 12:
R&TTE Compliance Statement—802.11
Page 13 and 14:
2Getting StartedOut of the BoxVerif
Page 15 and 16:
Step 4. Set the Time and DateOn the
Page 17 and 18:
Icons in the Navigation BarIndicato
Page 19 and 20:
To move an icon to the top of the S
Page 21 and 22:
3Hardware OverviewStandard Configur
Page 23 and 24:
Accessories for the 9700Each of the
Page 25 and 26:
Front Panel Features for the 9700Bl
Page 27 and 28:
Back Panel Features for the 9700Bat
Page 29 and 30:
Installing a Memory Card1. Press th
Page 31 and 32:
Using the Touch PanelHoneywell defi
Page 33 and 34:
BatteriesThere are two types of bat
Page 35 and 36:
The default values for these entrie
Page 37 and 38:
4Using the Scan Image EngineOvervie
Page 39 and 40:
DecodingThe terminal supports two t
Page 41 and 42:
Capturing ImagesThe image-capture p
Page 43 and 44:
5Using the Color CameraOverviewAll
Page 45 and 46:
MenuTap Menu on the Command Bar to
Page 47 and 48:
6Using the KeyboardsAvailable Keybo
Page 49 and 50:
Using the Modifier KeysName Key Fun
Page 51 and 52:
Key Normal Shift Blue Shift-Blue Bl
Page 53 and 54:
Key Normal Shift Blue Blue-Lock Red
Page 55 and 56:
7System SettingsOverviewCustomized
Page 57 and 58:
Personal MenuTo access the Personal
Page 59 and 60:
Additional FunctionsThe Assign a pr
Page 61 and 62:
5. Right-click on an empty area and
Page 63 and 64: BacklightThe Backlight system setti
Page 65 and 66: External GPSExternal GPS determines
Page 67 and 68: RILThe RIL Information screen displ
Page 69 and 70: 1. Tap Remove Programs. In the list
Page 71 and 72: Task ManagerThe Task Manager provid
Page 73 and 74: 8CommunicationConnections MenuThe C
Page 75 and 76: 5. When the IrDA port finds the ali
Page 77 and 78: *Proxy Server ConnectionsIf you are
Page 79 and 80: 4. When the radio is activated (i.e
Page 81 and 82: Setting Up the Host WorkstationVeri
Page 83 and 84: • If you want the program to be p
Page 85 and 86: 9Working with GSM/HSDPA/UMTS/GPRS/E
Page 87 and 88: Installing a SIM Card1. Press the P
Page 89 and 90: Volume ControlUse the Dolphin keybo
Page 91 and 92: Setup OptionsTap Menu > Options.The
Page 93 and 94: 4. Enter the Access point name. Tap
Page 95 and 96: Manual Network SelectionYou can sel
Page 97 and 98: 10Working with the Bluetooth RadioE
Page 99 and 100: 4. You are prompted to enter a pass
Page 101 and 102: Types of Devices and ServicesWhen y
Page 103 and 104: Transferring Files1. Tap Start > Fi
Page 105 and 106: 11Working with GPSOverviewThe Dolph
Page 107 and 108: 12Dolphin 9700 HomeBase DeviceOverv
Page 109 and 110: COMM LEDThis is the communication L
Page 111 and 112: Serial ConnectorThe following diagr
Page 113: CommunicationUSBDolphin terminals s
Page 117 and 118: 13Dolphin 9700 Mobile Base DeviceOv
Page 119 and 120: Bottom PanelThe power supply and RS
Page 121 and 122: MountingThe adjustable mounting bra
Page 123 and 124: Establishing CommunicationThe RS232
Page 125 and 126: 14Dolphin 9700 ChargeBase DeviceOve
Page 127 and 128: Power SupplyThe base includes a pow
Page 129 and 130: MountingThis base should be mounted
Page 131 and 132: 15Dolphin 9700 QuadCharger DeviceOv
Page 133 and 134: Supplying PowerThe charger must be
Page 135 and 136: TroubleshootingIf you encounter pro
Page 137 and 138: 16Customer SupportProduct Service a
Page 139 and 140: Limited WarrantyHoneywell Internati
Page 142: Honeywell Scanning & Mobility9680 O
show all

Dolphin 9700 User's Guide Rev (a) - Finn-ID

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?