Technical details System pro M compactÂ®

More documents

Recommendations

Info

Systempro M compact ®Technical detailsAccessories for measurementinstrumentsMeasurementdevicesTRANSDUCERS FOR POWER FACTOR METERSTechnical characteristics2CSC445093F0001Separated auxiliary supply [V] a.c. 230/400Input rated values [V] a.c. 230/400 (5 A)Output rated values (selectable)1, 5, 10 V d.c.1, 5, 10, 20, 4/20 mA d.c.Ohmic load [Ohm] 700Measurement fi eld0÷Pn (0÷Qn)Conversion typeproportional to phase angle or to cosϕAccuracy rating 0.5Permanent overload2 In/1.2 UnInstantaneous overload10 In/2 Un for 1 sec.Operating frequency [Hz] 50/60Time delay [ms] 300Alternated residue 1%Self-consumptionvoltage=1 VA/curr.=0.8 VA/aux. supply=4 VAInput/output galvanic separationinput/output insulation, aux. supply 2 kV for 1 min./50 Hzcircuit/mass insulation 4 kV for 1 min./50 HzOperating temperature [°C] 0...55Dimensions6 DIN modulesWeight [kg] 0.49Single-phase line and input and output selection10 V d.c.5 V d.c.1 V d.c.4÷20 mA d.c.20 mA d.c.10 mA d.c.5 mA d.c.1 mA d.c.1 mA d.c. (analogue signal)230 VCThe output selection must be performed by movingthe programming pushbuttons according to thespecific needs.SELECTABLE OUTPUTS- + + -N13 14 16 17 1923 24If a V output has been selected it is necessary toconnect terminals 13 and 14, while for mA outputsthe terminals 16 and 17 must be connected. Forsupplying the device at 230 V connect the commonterminal “C” and the terminal 23.Pushbutton for signal switch1 2 8Leftproportional to the cosϕ.11L1NS1P15 AS2P2VRightProportional to the phaseangle (output in grades, forinsertion with analogue reading instrument).Connect input voltage to terminal 8.Connect input current to terminals 1 and 2.2CSC445013F090111/110 ABB
Systempro M compact ®Technical detailsAccessories for measurementinstrumentsMeasurementdevicesBalanced three-phase line without neutral (3 wires)10 V d.c.5 V d.c.1 V d.c.4÷20 mA d.c.20 mA d.c.10 mA d.c.400 V 230 V5 mA d.c.1 mA d.c.1 mA CC (segnaleanalogico)CThe output selection must be performed bymoving the programming pushbuttons accordingto the specific needs.SELECTABLE OUTPUTS- + + -13 14 16 1721 23 24If a V output has been selected it is necessaryto connect terminals 13 and 14, while for mAoutputs the terminals 16 and 17 must beconnected. For supplying the device at 230 Vconnect the common terminal “C” and theterminal 23, while for a 400 V supply it isnecessary to connect the common terminal “C”and the terminal 21.L1L2L31 2 10 125 AVS1 S2P1 P2Pushbutton for signal switchLeftProportional to the cosϕ.RightProportional to the phase angle(output in grades, for insertionwith analogue reading instrument).Connect input voltage to terminals 10 and 12.Connect input current of L1 phase to terminals1 and 2.2CSC445014F090111ABB11/111
Page 1 and 2:
Systempro M compact ®Technical det
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60: Systempro M compact ®Technical det
Page 91 and 92: 124681246Systempro M compact ®Tech
Page 109: Systempro M compact ®Technical det
Page 115: Systempro M compact ®Technical det
show all

Technical details System pro M compactÂ®

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?