Download Glorystar Installation Guide - Free Christian Satellite ...

More documents

Recommendations

Info

36To correct a warped reflector, hold the dishlike a steering wheel and quickly thrust thereflector away from your body like the motionof passing a basketball. This action willcause the reflector to slightly flex and springback into the factory pressed shape. Checkfor correction with the string test. It may benecessary to repeat the flexing process severaltimes until the reflector edges are uniformlyflat.Important Note:An assembled dish will not be accepted for refund.GEOSATpro 90cm Dish HardwareItem Quantity Description Size1 6 Carriage Bolt 1/4” x 1/2”2 2 Phillips Screw M4 - 16m3 2 Hex Nut M44 13 Hex Nut 1/4”5 1 Carriage Bolt 1/4” x 1 1/4”6 1 Structural Bolt 1/4” x 2 1/2”7 2 Elevator Bolt 1/4” x 1 1/4”8 2 Washer 1/4”9 2 Carriage Bolt 1/4” x 3/4”10 2 Phillips Bolt 1/4” x 1/2”11 2 Hex Nut 1/4”12 1 Phillips Bolt 1/4” x 1 1/4”A 4 Hex Flange Bolt 1/4” x 1/2”B 1 Hex Nut 1/4”C 1 Hex Tap Bolt 1/4” x 3 1/2”D 1 Fastener InsertPlease contact your reseller if any of these parts are missing or damaged. Mostreplacement hardware items can be purchased at a local hardware supply store.B. Gohl © GEOSATpro
37Attach the LNBF Arm to the Elevation Bracket.Assemble the Elevation Bracket and PostClamp. The Post Clamp has two holesdrilled. One hole is stamped with an A and the other with a B.Assemble the Elevation Bracket to thePost Clamp inserting Structural Bolt A(part #6) through the hole stamped A ifthe Dish Elevation Angle is between 10 -60 degrees. Assemble using hole stampedB if the elevation angle is to be between50 – 90 degrees. Most installations inthe US and Canada will use ElevationScale A type assembly. <strong>Installation</strong>s inMexico will usually use Elevation ScaleB assembly.The dish has been correctly assembledfor Measuring the Dish ElevationAngle using Scale A (10 - 60 degrees)if a letter B is visible stamped on thePost Clamp on the left side of the PostClamp.After verifying the Reflector is not warped,mount the Reflector to the ElevationBracket and install the two LNBF ArmSide Supports. The Side Arm Supports willperfectly center and support the LNBFs foroptimal reception.www.geosatpro.com Toll <strong>Free</strong> 888-483-4673
Page 2 and 3: Owners ManualInstallation GuideVers
Page 5 and 6: Important Safeguardswww.geosatpro.c
Page 7 and 8: DSR200c / DVR1100c SpecificationsMP
Page 9 and 10: Rear Panel12345678910111213Connects
Page 11 and 12: Remote Key Functions DSR200c / DVR1
Page 13 and 14: Receiver Operation Guide11Program I
Page 15 and 16: Stereo or Mono Audio Selectiona) Pr
Page 17 and 18: Receiver Menu ItemsPress MENU butto
Page 19 and 20: www.geosatpro.com Toll Free 888-483
Page 21 and 22: 1. Press RED button to exit - no mo
Page 23 and 24: 21Highlight Control Panel. Press OK
Page 25 and 26: Highlight USB. Press OK.This menu s
Page 27 and 28: 25V-1. Time Machine - DVR1100cTime
Page 29 and 30: 27Timer - DVR1100cIf no event infor
Page 31 and 32: Installation Guides29This guide is
Page 33 and 34: Site Survey31If you feel comfortabl
Page 35 and 36: 33How High Up in the Sky is the Sat
Page 37: Dish Assembly35Once a dish location
Page 41 and 42: Center the bubble in the level then
Page 43 and 44: When setting the elevationangle on
Page 45: Connect Receiver to a TVThe easiest
Page 48 and 49: 46The Glorystar receiver will autom
Page 50 and 51: 48Press the CH/DOWN arrowbutton on
Page 52 and 53: 50Two Room Install - (optional)Do n
Page 54 and 55: 527. Press the RIGHT arrow to selec
Page 56 and 57: 54Using Satellite MetersInexpensive
Page 58 and 59: 56FAQ - Frequently Asked QuestionsH
Page 60 and 61: 58FAQ - DVR1100c - cont.USB drive m

Download Glorystar Installation Guide - Free Christian Satellite ...

Create successful ePaper yourself

Delete template?

Save as template?