Download Glorystar Installation Guide - Free Christian Satellite ...

More documents

Recommendations

Info

54Using Satellite MetersInexpensive satellite meters can speedup the installation process, but they onlydisplay the signal strength of a satellite.It is important to understand that signalstrength satellite meters do not indicate ifthe dish is aimed at the correct satellite and they will not be usefulfor fine tuning the dish aiming or adjusting LNBF skew (rotation).Signal strength meters must be used along with the satellite receiverto determine if the dish is aimed at the correct satellite.A digital identification meter such as a SatBuddy or BirDog willsimplify the installation process. Please consult with the ownersmanual for correct operation. We recommend the Super SatBuddy.Install Procedure with a Signal Identification MeterConnect LNBF and use a data set for standard LNB type LO 10750,KU, Galaxy 19 97W, Horizontal and Vertical transponders. Peak andBalance for maximum Signal Quality (Q) for G 19. Verify the SignalQuality averaged above 50% on the Glorystar receiver channels 901,106 and 113. Perform an OTA update following directions on Page49 of this guide to update the channel list.Note: Birdog meters may have difficulty detecting weaker FSS typesignals and must have the BER setting changed in the main set-upmenu. Change the BER setting to LOG (logarithmic) and the meterwill become much more sensitive to the weaker FSS type satellites.Professional Installer Tip:If you are having trouble locating the satellite, remove the Glorystarstandard linear polarity LNBF from the clamp and install a DirecTVcircular polarity LNBF. Locate the DirecTV 101w satellite with yourmeter or a DirecTV receiver. Mark the mast and mast clamp with the101W satellite position. Replace the Glorystar linear polarity LNBFinto the clamp and set the skew. Rotate the dish approximately 6degrees to the East (1/4” on the mast marking). The dish is nowroughly aimed and will only require fine AZ/EL tuning for optimalreception of the Galaxy 19 satellite @ orbital slot 97W.B. Gohl © GEOSATpro
Carefully route the coax cable fromthe dish to the ground block thento the satellite receiver. Secure allcables using appropriate cable clipsand nylon zip ties. Avoid usingwire staples as they can dimple orpenetrate the cable and can causeloss of signal! Form drip loops andcable loops as needed to preventwater from running down the cables and entering cable connectionfittings or into wall penetrations. Remember to seal all exterior walland/or roof holes with a quality sealant or silicone caulking.Install the grounding block andwire while observing all NEC,National Electrical Code and localcodes. Connect the ground wire tothe structure ground. If you areunsure of how to properly groundyour satellite system, pleaseconsult with a local professional.Copies of the NEC are available atyour local library or online.Important Notice: GEOSATpro recommends that you DO NOTuse existing coaxial cabling that has been pre-wired or previouslyused in your home. Often these cables are low quality RG-59, notrated for satellite applications or have splitters and other devicesthat are not compatible. Always connect the RG-6 type coax cabledirectly from the satellite dish LNBF through the grounding blockand attach to the LNBF IN Digital connection on the rear of theSatellite Receiver.Cable splitters and other devices in the coax line may cause thesatellite receiver to shut down or malfunction. Do not use any devicein the coax line unless approved for satellite installation. Multiplereceiver installations must use a multiple output LNBF to avoidtuning conflicts between the receivers. Splitters will not work!www.geosatpro.com Toll Free 888-483-467355Completing the Install and Grounding
Page 2 and 3:
Owners ManualInstallation GuideVers
Page 5 and 6: Important Safeguardswww.geosatpro.c
Page 7 and 8: DSR200c / DVR1100c SpecificationsMP
Page 9 and 10: Rear Panel12345678910111213Connects
Page 11 and 12: Remote Key Functions DSR200c / DVR1
Page 13 and 14: Receiver Operation Guide11Program I
Page 15 and 16: Stereo or Mono Audio Selectiona) Pr
Page 17 and 18: Receiver Menu ItemsPress MENU butto
Page 19 and 20: www.geosatpro.com Toll Free 888-483
Page 21 and 22: 1. Press RED button to exit - no mo
Page 23 and 24: 21Highlight Control Panel. Press OK
Page 25 and 26: Highlight USB. Press OK.This menu s
Page 27 and 28: 25V-1. Time Machine - DVR1100cTime
Page 29 and 30: 27Timer - DVR1100cIf no event infor
Page 31 and 32: Installation Guides29This guide is
Page 33 and 34: Site Survey31If you feel comfortabl
Page 35 and 36: 33How High Up in the Sky is the Sat
Page 37 and 38: Dish Assembly35Once a dish location
Page 39 and 40: 37Attach the LNBF Arm to the Elevat
Page 41 and 42: Center the bubble in the level then
Page 43 and 44: When setting the elevationangle on
Page 45: Connect Receiver to a TVThe easiest
Page 48 and 49: 46The Glorystar receiver will autom
Page 50 and 51: 48Press the CH/DOWN arrowbutton on
Page 52 and 53: 50Two Room Install - (optional)Do n
Page 54 and 55: 527. Press the RIGHT arrow to selec
Page 58 and 59: 56FAQ - Frequently Asked QuestionsH
Page 60 and 61: 58FAQ - DVR1100c - cont.USB drive m
show all

Download Glorystar Installation Guide - Free Christian Satellite ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?