animeoÂ® KNX 4 DCE Motor Controller WM/DRM 220-240 V AC

More documents

Recommendations

Info

2 Assembly63 mmmin.120 mm140 mmMounting of the Motor Controller 4 DC/E WMSwitch boxComplete wiring and connectpower supplyDIN railBus> 10 cmBus3 Wiring diagramEncodermotor 1LW25-E83Encodermotor 2LW25-E83Encodermotor 3LW25-E83Encodermotor 4LW25-E83Motor 24 V DC(without Encoder)M˜purpleM˜purpleM˜purpleM˜purpleM˜LV 25 B44, B64LW 25, B44, B83LT 28 B730.25 mm 2 2 EL1NPE1 2 3Junctionbox1 2 30.25 mm 2Junctionbox1 2 30.25 mm 2Junctionbox1 2 30.25 mm 2Junctionboxalternatively1 20.25 mm 2-mains230 V50 HzLL N N12 EM112 EM212 EM312 EM41MxIn1-4COut1-4CSCREUUSReset / Prog1 A BCSomfyanimeo KNX4 DC/E Motor Controller WM18601272 C DC3 E FC4GHCKNX LEDKNX ProgBus- +bl rdanimeoRTS module 433.42 MHz1860105GroupcontrolCUPDown+UPDown+UPDown+UPDown+UPDown+ red- blackKNX bus cable2 x 2 x 0.8 mm 2 (green)Local push buttonMotor 1Local push buttonMotor 2Local push buttonMotor 3Local push buttonMotor 4Local push button inputs can be used as binary inputs!animeo KNX 4 DC/E Moco • Ref. 5055608B - 6/54
3.1 Motor outputsMax. current per output: 500 mA.Compatibel with the following Somfy motors in combination with the CTS 25 enrolling system for Venetian blinds:LV 25-B44, -B64DC-Mode2 wiresLW 25-B44, -B83DC Mode2 wiresLW 25-E83DCE- Mode3 wiresLT 28-B73DC Mode2 wiresStehleJ 1012 wiresm Control of non Somfy motors only on request3.2 CablingmAs soon as the 230 V and the KNX bus voltage supply are attached, the "US" LED blinksregularly. The device is operational when the "US" LED is blinking continuously.CABLEConnections to Cables Twisted pairs Max. distanceMotorsSwitchesGroup controlMin.: 3 x 0.6 mm/22 AWGMax.: 3 x 2.5 mm 2 /14 AWGMin.: 3 x 0.6 mm/22 AWGMax.: 3 x 2.5 mm 2 /14 AWGMin.: 3 x 0.6 mm/22 AWGMax.: 3 x 1.5 mm 2 /16 AWG— 20 mRecommendedRecommendedKNX Bus 2 x 0.8 mm/20 AWG Required, following KNX topologyguidelines220 - 240 V AC Min.: 3 x 1.5 mm 2 /16 AWGMax.: 3 x 2.5 mm 2 /14 AWG—100 m50 m3.3 Checking the move directions of the end productsGroup control of the motors 1 - 4 over the group control inputThe move directions of the motors can be checked via the group inputs. All four motor outputs are switched simultaneously. This input canbe blocked in the ETS parameters. In the event of bus power failure, it is always freed to allow emergency operation.m When starting up, make absolutely sure that the motors move in the right direction. This check can be carried out by making a wiringbridge at the group input.Check the correct move direction of the end productDOWN: The end product moves down (bridge between C + )STOP: The end product stops (bridge between C + + )UP: The end product moves upwards (C + )animeo KNX 4 DC/E Moco • Ref. 5055608B - 7/54
Page 2 and 3: Table of contentsIntroduction......
Page 8 and 9: 3.4 Checking the turning direction
Page 11 and 12: 4.5 Manual setting of the intermedi
Page 13 and 14: No. Object name Type DPT_ID Descrip
Page 21 and 22: Motor output configurationOptions:
Page 23: Group control inputOptions:• Disa
Page 26 and 27: The following parameter description
Page 28 and 29: 6.5 Menue index card "Functions Mot
Page 30 and 31: Repeat last telegram after security
Page 32 and 33: Edge evaluation contact AOptions:
Page 34 and 35: Basic functionOptions:• Venetian
Page 36 and 37: Contact type input AOptions:• Nor
Page 38 and 39: 6.8 Menue index card "Bus safety"On
Page 40 and 41: MOTOR 1 ... 4Feedback ofOptions:•
Page 42 and 43: Cyclic montoring time in sec. (0-25
Page 44 and 45: Radio binary input 1 ... 5For every
Page 46 and 47: Functionality of the "UP" push butt
Page 48 and 49: Basic functionOptions:• Venetian
Page 50 and 51: 7 Diagnosis7.1 LEDs on the animeo K
Page 52 and 53: 8 Push button configuration of the
Page 54:
iwww.somfy.com/DFS/manuals/AUSTRIAS
show all

animeoÂ® KNX 4 DCE Motor Controller WM/DRM 220-240 V AC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?