Control Systems - Uniclima

More documents

Recommendations

Info

1 Individual control system3. Wired remote controller1) MWR-WS00(4) Additional functionsFunction keysTracking functionFunction If an additional indoor unit is connected to the wired remote controller, If a connected indoor unit is deleted. If wired remote controller is replaced.it is compulsory to carry out Tracking in the wired remote controller for indoor units.Press both Set button and Cancel button on the wired remote controller for 5 seconds.Then LCD backlight is turned on again and the temperature display is shown.At this time, there is no change in the operation status of the indoor unit.<strong>Control</strong> Tracking is underway.Option switchAble to set an additional function for wired remote controllerwith the 8 option switches on the PCB of wired remote controller. Default switch settings are all OFF.Switch No. OFF ONSW 1SW 2SW 3For cooling and heating modelAble to use both wireless remote controller andwired remote controller for indoor unit control.If two wired remote controllers are used to control1 indoor unit (group), it is set as a master wiredremote controller.For cooling model only (If the operation mode is selected,heating operation display is skipped.)Unable to use wireless remote controller.If two wired remote controllers are used to control1 indoor unit (group), it is set as a Slave wired remotecontroller.SW 4 Temperature display in Celsius (°C). Temperature display in Fahrenheit (°F).SW 5SW 6Use the temperature sensor in the indoor unit forindoor unit control.No functionSW 7 No function No functionSW 8 Service mode monitoring Service mode settingUse the temperature sensor in the wired remotecontroller for indoor unit control.Use the average value of temperature sensors of wiredremote controller and indoor unit for indoor unit control. Note If SW5 is ON, then “Setting temperature compensation under the heating mode” is set to 0°C(0°F). After setting option switch, wired remote controller power reset is required.14
Temperature control with built-in temperature sensorIndividual control systemTemperature sensor in the wired remote controller can be appliedto all the connected indoor units of DVM Plus II/III.DIP SwitchSW 5SW 6FunctionOFF Use the temperature sensor in the indoor unit.ONOFFONUse the temperature sensor in the wired remote control.Reserved.Use the average value of the temperature sensors in theindoor unit(s) and the wired remote controller(SW5 in ON).Here, the wired remote controller chooses the indoor unitof the lowest MAIN address, or one of the indoor units atrandom.Heating mode temperature compensationDVM Plus III 4way PCBK5DIP SwitchSW 5Function+2°C(3.6°F), +5°C(9°F) temperature compensation.DIP SwitchFunctionSW 5 OFF Use the temperature sensor in the wired remote control.What happens to heating mode temperature compensation [+2°C(3.6°F), +5°C(9°F)] when the use of thewired R/C built-in temperature is enabled ?• The heating mode temperature compensation is cleared. [0°C(0°F)]• If you want to use compensation, set value in the service mode menu 8.15
Page 3 and 4: Control Systems
Page 5 and 6: III. Integrated management system12
Page 7: I. Individual control system1 Wirel
Page 12 and 13: 1 Individual control system3. Wired
Page 27 and 28: (4) Additional functionsTracking fu
Page 29 and 30: Power failure of wired remote contr
Page 31 and 32: Service mode menu descriptionIndivi
Page 33 and 34: Menu Detailed description DisplayEE
Page 35 and 36: E.Saver - Energy saving operation m
Page 37 and 38: (3) Description of buttons and func
Page 39 and 40: CAUTION During operation mode lock,
Page 41 and 42: Operation checkingOperationDisplayI
Page 43 and 44: Connection examplesIndividual contr
Page 45: Group control (4)Control multiple i
Page 48 and 49: DVM PLUS III46
Page 50 and 51: 2 Centralized control system1. Inte
Page 52 and 53: 0123456789ABCDEF2 Centralized contr
Page 54 and 55: 2 Centralized control system1. Inte
Page 56: 2 Centralized control system2. Cent
Page 60 and 61: 2 Centralized control system2. Cent
Page 62 and 63: 2 Centralized control system2. Cent
Page 64 and 65:
2 Centralized control system2. Cent
Page 66 and 67:
2 Centralized control system3. Oper
Page 68 and 69:
2 Centralized control system3. Oper
Page 70 and 71:
DVM PLUS III68
Page 72 and 73:
3 Integrated management system1. DM
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
3 Integrated management system2. S-
Page 92 and 93:
Page 94:
Page 97 and 98:
Control• Control indoor unit/ERV
Page 99 and 100:
The 3 rd step (schedule operation s
Page 101 and 102:
Power management structure editing
Page 103 and 104:
System management Environment setti
Page 105 and 106:
DMS backup and restoration• Able
Page 107 and 108:
(3) S-NET3 log informationLogE9000E
Page 109 and 110:
3) Main panel12345678LAN connection
Page 111 and 112:
Pattern 3Option switchDI-2DI-1Exter
Page 113:
7) Menu(1) Main menu 1 234 5 6 7 8N
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
DVM PLUS III118
Page 122 and 123:
4 External contact control system1.
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132:
Page 136:
Control SystemsSamsung Electronics
show all

Control Systems - Uniclima

Create successful ePaper yourself

Delete template?

Save as template?