Control Systems - Uniclima

More documents

Recommendations

Info

1 Individual control system3. Wired remote controller1) MWR-WS00(4) Additional functionsPower failure of wired remote controller1 Temperature control with built-in temperature sensorWhat if communication block occurs on the wired remote controller when its built-in temperature use is enabled ?(Block due to either power failure or disconnection only)• When communication is blocked over 3 minutes, Indoor unit ignores the built-in temperature sensor and accepts its sensor in the indoor unit. Ignores heating mode temperature compensation setting by the remote controller and acceptsK5 switch setting on the indoor unit PCB.• When communication resumes, Built-in temperature use is recovered. Setting temperature compensation in heating mode changes to 0°C(0°F).2 Recovery of parameter settingFunction Power failure recovery Parameter storageCurrent time YES (for 2 days) Wired R/CSchedule setting YES Wired R/CBuilt-in temperature sensor Compensation NO (re-setting required) Wired R/CIndoor unit RMC address YES Indoor unitOption code setting YES Indoor unitButton lock setting NO (re-setting required) NONEUpper/Lower set temperature limit YES Wired R/CAutomatic Stop YES Wired R/CFan direction setting NO (re-setting required) NONEIndoor unit RPM compensation NO (re-setting required) NONEStop EEV step under Heating mode NO (re-setting required) NONEFilter replacement time NO (re-setting required) NONEIndoor unit heating compensation[+2°C(3.6°F), +5°C(9°F]NO (re-setting required)NONE16
Service mode menu descriptionIndividual control systemPress Hr., Min., and temperature setting buttonfor more than 5 seconds to enter Service mode.Menu Detailed description DisplaySW 8 OFF: Option code monitoringSW 8 ON: Option code settingOption code : Detailed indoor unit functions such as indoor unit modeltype, indoor unit capacity, blackoutrestoration, and drain pump control are set by thecombination of 12-digit or 24-digit numbers.(ex. 0d7800-198091-200001-300000)SW 8 OFF : Indoor unit address monitoringSW 8 ON : Indoor unit address ( RMC address only)settingIndoor unit address:Address used for indoor unit communication andcontrol(Set by a rotary switch of the indoor unit PCB)1) Main address: Indoor unit’s physical address2) RMC address: Address used in the central controlRMC (1) : Interface module channel addressRMC (2) : Indoor unit group addressSW 8 OFF / ON: Monitor indoor unit cycle dataMenuData1 Indoor temperature2 EVA-IN temperature3 EVA-OUT temperature4 EEV stepMain addressMenuLeft: RMC (1) addressRight: RMC (2) addressData17
Page 3 and 4: Control Systems
Page 5 and 6: III. Integrated management system12
Page 7: I. Individual control system1 Wirel
Page 12 and 13: 1 Individual control system3. Wired
Page 27 and 28: (4) Additional functionsTracking fu
Page 29 and 30: Power failure of wired remote contr
Page 31 and 32: Service mode menu descriptionIndivi
Page 33 and 34: Menu Detailed description DisplayEE
Page 35 and 36: E.Saver - Energy saving operation m
Page 37 and 38: (3) Description of buttons and func
Page 39 and 40: CAUTION During operation mode lock,
Page 41 and 42: Operation checkingOperationDisplayI
Page 43 and 44: Connection examplesIndividual contr
Page 45: Group control (4)Control multiple i
Page 48 and 49: DVM PLUS III46
Page 50 and 51: 2 Centralized control system1. Inte
Page 52 and 53: 0123456789ABCDEF2 Centralized contr
Page 54 and 55: 2 Centralized control system1. Inte
Page 56: 2 Centralized control system2. Cent
Page 60 and 61: 2 Centralized control system2. Cent
Page 66 and 67: 2 Centralized control system3. Oper
Page 68 and 69:
2 Centralized control system3. Oper
Page 70 and 71:
DVM PLUS III68
Page 72 and 73:
3 Integrated management system1. DM
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
3 Integrated management system2. S-
Page 92 and 93:
Page 94:
Page 97 and 98:
Control• Control indoor unit/ERV
Page 99 and 100:
The 3 rd step (schedule operation s
Page 101 and 102:
Power management structure editing
Page 103 and 104:
System management Environment setti
Page 105 and 106:
DMS backup and restoration• Able
Page 107 and 108:
(3) S-NET3 log informationLogE9000E
Page 109 and 110:
3) Main panel12345678LAN connection
Page 111 and 112:
Pattern 3Option switchDI-2DI-1Exter
Page 113:
7) Menu(1) Main menu 1 234 5 6 7 8N
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
DVM PLUS III118
Page 122 and 123:
4 External contact control system1.
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132:
Page 136:
Control SystemsSamsung Electronics
show all

Control Systems - Uniclima

Create successful ePaper yourself

Delete template?

Save as template?