Manual Samsung SCU-VAC/VAC1 Positioning System

More documents

Recommendations

Info

connection & installationPower Module Connection Diagram The power adaptor (AC) has no polarity.M The maximum power capacity of the built-in relay is 30VDC/2A, 125VAC/0.5A, and 250VAC/0.25A.A separate relay driver device is required if used with an adaptor which exceeds specifi ed nominal specifi cations.Connecting the power connector and GND incorrectly to the NC/NO and COM ports may cause a short circuit and fi re,damaging the camera.CAMERA AND APPLIANCES WIRING DIAGRAMConnecting with Samsung Techwin’s “Stand Alone DVR”RS-485 :CameraRXD+RXD-Stand Alone DVRT(TXD)+T(TXD)-RS-422 :CameraRXD+RXD-TXD+TXD-Stand Alone DVRT(TXD)+T(TXD)-R(RXD)+R(TXD)-16_ connection & installation
CAMMENUSEARCHMULTIRECMONESCMENUPRESETGROUPTRACKConnecting with the Samsung Techwin Controller SPC-6000RS-485 :CameraRXD+RXD-RS-422 :CameraTXD+TXD-RXD+RXD-To connect to Samsung PC DVRTXD+TXD-RXD+RXD-TXD+TXD-TX RX TX RXG+ - + - + - + -TX RX TX RXG+ - + - + - + -1 2 3 4 56 7 8 9 0PTZ DVR MTX SETUPFUNC ENTERCLOSE OPENNEAR FARWIDE TELE● CONNECTION & INSTALLATIONRS-485 :CameraRXD+RXD-PC DVRSRP-1610/1650English - 17
Page 1 and 2: Positioning SystemUser ManualSCU-23
Page 3 and 4: safety informationCAUTIONRISK OF EL
Page 5 and 6: important safety instructions1. Rea
Page 9 and 10: SCU-2370SCU-9051SCU-VACSCU-VAC1WHAT
Page 11 and 12: Back● INTRODUCTION❶➋➌➍❶
Page 13 and 14: CCTV ZOOM LENZSLA-12240 12-240mm 1:
Page 15: Camera Wiring Interface BoardFor th
Page 19 and 20: Communication Method SettingsSelect
Page 21 and 22: CAMERA ID DIP SWITCH SETTINGSAssign
Page 23 and 24: CAMMENUSEARCHMULTIRECMONPTZ DVR MTX
Page 25 and 26: To install the light projector1. Fi
Page 27 and 28: USING AND SETTING THE MENUSOSD (On-
Page 29 and 30: CAMERA SETUP (SCU-2370) The camera
Page 31 and 32: White BalanceThe White Balance menu
Page 33 and 34: Back LightUnlike other cameras, Sam
Page 35 and 36: AGC(Auto Gain Control)AGC (Automati
Page 37 and 38: SSDR(Samsung Super Dynamic Range)SS
Page 39 and 40: OthersSync : Enables selecting Inte
Page 41 and 42: Comm. Setting (SCU-9051)- Parity: Y
Page 43 and 44: NUC (Calibration)4.Press the SET bu
Page 45 and 46: SPECIAL (Environment Settings Mode)
Page 47 and 48: Sequence SettingPresetThis function
Page 49 and 50: MD Function’s Prerequisite when u
Page 51 and 52: Home PositionSets one of the curren
Page 53 and 54: Group SEQSelecting Group SEQ recall
Page 55 and 56: Auto RunIf there is no controller o
Page 57 and 58: P/T SettingPan/Tilt LimitThe moving
Page 59 and 60: Area Masking (SCU-2370/VAC/VAC1)If
Page 61 and 62: Wiper (SCU-2370/VAC/VAC1)You can us
Page 63 and 64: Image Hold (SCU-2370)While in Group
Page 65 and 66: ALARM SETTINGSetting Up Alarm Input
Page 67 and 68:
M Connecting the power connector a
Page 69 and 70:
Camera Default Set : (SCU-2370)This
Page 71 and 72:
Problem Cause and Solution Page►
Page 73 and 74:
product specificationsPRODUCT SPECI
Page 75 and 76:
Pan / TiltPan Range360° EndlessSCU
Page 77 and 78:
EXTERNAL DIMENSIONS (SCU-2370/VAC/9
Page 79 and 80:
EXTERNAL DIMENSIONS (SCU-VAC1)● P
Page 81 and 82:
Wall Mount72.16.5153.7● PRODUCT S
Page 83 and 84:
MEMO
Page 85 and 86:
MEMO
show all

Manual Samsung SCU-VAC/VAC1 Positioning System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?