Manual Samsung SCU-VAC/VAC1 Positioning System

More documents

Recommendations

Info

connection & installationCOMMUNICATION PROTOCOL DIP SWITCH SETTINGSCoaxial communication automatically detects signals, and so does not require a separate communicationsetup process.Pin No.Purpose1 ~ 4 Protocol Settings5 Transfer Method (RS-485/422) Settings6 Response Mode Settings7 Terminal Resistance TX8 Terminal Resistance RX9 TEST10 Factory DefaultProtocol SettingsSelect a communication protocol for the camera.No Protocol #4 #3 #2 #11 SAMSUNG-T OFF OFF OFF OFF2 SAMSUNG-E OFF OFF OFF ON3 Pelco-D OFF OFF ON OFF4 Pelco-P OFF OFF ON ON5 Panasonic OFF ON OFF OFF6 Vicon OFF ON OFF ON7 Honeywell OFF ON ON OFF8 AD OFF ON ON ON8 GE ON OFF OFF OFF10 Bosch ON OFF OFF ON18_ connection & installation
Communication Method SettingsSelect a communication method for the camera.Function ON OFF#5 Transfer Mode Switch RS-422(4Wire) RS-485(2Wire)Communication Response SettingsSelect a communication response method for the camera and controller: Response or No Response.Function ON OFF#6 Response Mode Switch Response No ResponseTermination Settings● CONNECTION & INSTALLATIONTo prevent the attenuation of communication signals between the camera and controller, the items atthe end of line must be set up with the termination settings.Camera Input Position #7 #8Terminal Resistance TX ON OFFTerminal Resistance RX OFF ONI When terminating for RS-485: #8 ONWhen terminating for RS-422: #7, #8 ONInitializeInitialize the system using the Initialize switch on the rear of the product.Once initialized, all current settings will return to the factory default.InitializeDo not use initialization#10 ON OFFI If you do not set the Reset witch to OFF after resetting the system, all stored data will be lost when you restart thesystem.English - 19
Page 1 and 2: Positioning SystemUser ManualSCU-23
Page 3 and 4: safety informationCAUTIONRISK OF EL
Page 5 and 6: important safety instructions1. Rea
Page 9 and 10: SCU-2370SCU-9051SCU-VACSCU-VAC1WHAT
Page 11 and 12: Back● INTRODUCTION❶➋➌➍❶
Page 13 and 14: CCTV ZOOM LENZSLA-12240 12-240mm 1:
Page 15 and 16: Camera Wiring Interface BoardFor th
Page 17: CAMMENUSEARCHMULTIRECMONESCMENUPRES
Page 21 and 22: CAMERA ID DIP SWITCH SETTINGSAssign
Page 23 and 24: CAMMENUSEARCHMULTIRECMONPTZ DVR MTX
Page 25 and 26: To install the light projector1. Fi
Page 27 and 28: USING AND SETTING THE MENUSOSD (On-
Page 29 and 30: CAMERA SETUP (SCU-2370) The camera
Page 31 and 32: White BalanceThe White Balance menu
Page 33 and 34: Back LightUnlike other cameras, Sam
Page 35 and 36: AGC(Auto Gain Control)AGC (Automati
Page 37 and 38: SSDR(Samsung Super Dynamic Range)SS
Page 39 and 40: OthersSync : Enables selecting Inte
Page 41 and 42: Comm. Setting (SCU-9051)- Parity: Y
Page 43 and 44: NUC (Calibration)4.Press the SET bu
Page 45 and 46: SPECIAL (Environment Settings Mode)
Page 47 and 48: Sequence SettingPresetThis function
Page 49 and 50: MD Function’s Prerequisite when u
Page 51 and 52: Home PositionSets one of the curren
Page 53 and 54: Group SEQSelecting Group SEQ recall
Page 55 and 56: Auto RunIf there is no controller o
Page 57 and 58: P/T SettingPan/Tilt LimitThe moving
Page 59 and 60: Area Masking (SCU-2370/VAC/VAC1)If
Page 61 and 62: Wiper (SCU-2370/VAC/VAC1)You can us
Page 63 and 64: Image Hold (SCU-2370)While in Group
Page 65 and 66: ALARM SETTINGSetting Up Alarm Input
Page 67 and 68: M Connecting the power connector a
Page 69 and 70:
Camera Default Set : (SCU-2370)This
Page 71 and 72:
Problem Cause and Solution Page►
Page 73 and 74:
product specificationsPRODUCT SPECI
Page 75 and 76:
Pan / TiltPan Range360° EndlessSCU
Page 77 and 78:
EXTERNAL DIMENSIONS (SCU-2370/VAC/9
Page 79 and 80:
EXTERNAL DIMENSIONS (SCU-VAC1)● P
Page 81 and 82:
Wall Mount72.16.5153.7● PRODUCT S
Page 83 and 84:
MEMO
Page 85 and 86:
MEMO
show all

Manual Samsung SCU-VAC/VAC1 Positioning System

Create successful ePaper yourself

Delete template?

Save as template?