Manual Samsung SCU-VAC/VAC1 Positioning System

More documents

Recommendations

Info

connection & installationCAMERA INSTALLATIONPedestal MountWall MountM Do not connect the camera to a power outlet until the installation is complete. Supplying power in the middle of theinstallation may cause fi re or damage the product.Bend back the wiper before opening the housing.Ensure that the housing is closed completely before you turn on the product. Do not reset the system with the housingopen. Otherwise, it may cause damage to the product.24_ connection & installation
To install the light projector1. Fix 4 hex screws to secure the camera on the bracket through theholes prepared, from the bottom side of the bracket.2.To secure the light projector on the bracket, fi x 4 hex screws throughthe holes prepared on the boundary of the bracket, from the bottomside. Fix the center hex screw from the upper side of the bracketmount towards the light projector.* Mounting and securing the light projector may vary depending onthe light projector type.● CONNECTION & INSTALLATION3.Connect the cables.4.Insert the projector cables through the rear hole of the camera.5. Light projector cable is to be connected to the power module.English - 25
Page 1 and 2: Positioning SystemUser ManualSCU-23
Page 3 and 4: safety informationCAUTIONRISK OF EL
Page 5 and 6: important safety instructions1. Rea
Page 9 and 10: SCU-2370SCU-9051SCU-VACSCU-VAC1WHAT
Page 11 and 12: Back● INTRODUCTION❶➋➌➍❶
Page 13 and 14: CCTV ZOOM LENZSLA-12240 12-240mm 1:
Page 15 and 16: Camera Wiring Interface BoardFor th
Page 17 and 18: CAMMENUSEARCHMULTIRECMONESCMENUPRES
Page 19 and 20: Communication Method SettingsSelect
Page 21 and 22: CAMERA ID DIP SWITCH SETTINGSAssign
Page 23: CAMMENUSEARCHMULTIRECMONPTZ DVR MTX
Page 27 and 28: USING AND SETTING THE MENUSOSD (On-
Page 29 and 30: CAMERA SETUP (SCU-2370) The camera
Page 31 and 32: White BalanceThe White Balance menu
Page 33 and 34: Back LightUnlike other cameras, Sam
Page 35 and 36: AGC(Auto Gain Control)AGC (Automati
Page 37 and 38: SSDR(Samsung Super Dynamic Range)SS
Page 39 and 40: OthersSync : Enables selecting Inte
Page 41 and 42: Comm. Setting (SCU-9051)- Parity: Y
Page 43 and 44: NUC (Calibration)4.Press the SET bu
Page 45 and 46: SPECIAL (Environment Settings Mode)
Page 47 and 48: Sequence SettingPresetThis function
Page 49 and 50: MD Function’s Prerequisite when u
Page 51 and 52: Home PositionSets one of the curren
Page 53 and 54: Group SEQSelecting Group SEQ recall
Page 55 and 56: Auto RunIf there is no controller o
Page 57 and 58: P/T SettingPan/Tilt LimitThe moving
Page 59 and 60: Area Masking (SCU-2370/VAC/VAC1)If
Page 61 and 62: Wiper (SCU-2370/VAC/VAC1)You can us
Page 63 and 64: Image Hold (SCU-2370)While in Group
Page 65 and 66: ALARM SETTINGSetting Up Alarm Input
Page 67 and 68: M Connecting the power connector a
Page 69 and 70: Camera Default Set : (SCU-2370)This
Page 71 and 72: Problem Cause and Solution Page►
Page 73 and 74: product specificationsPRODUCT SPECI
Page 75 and 76:
Pan / TiltPan Range360° EndlessSCU
Page 77 and 78:
EXTERNAL DIMENSIONS (SCU-2370/VAC/9
Page 79 and 80:
EXTERNAL DIMENSIONS (SCU-VAC1)● P
Page 81 and 82:
Wall Mount72.16.5153.7● PRODUCT S
Page 83 and 84:
MEMO
Page 85 and 86:
MEMO
show all

Manual Samsung SCU-VAC/VAC1 Positioning System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?