CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT CONELOG ® IMPLANT POSITION PLANNING SPLINTED CROWNS In the event of unfavorable leverage relations around the implant, a choice must be made between a longer implant or, if this is anatomically impossible, splinting adjacent crowns. If splinting is required by reason of statics, then hygienic requirements must also be taken into account. Development of a uniform insertion direction for the crown block must be part of the abutment preparation. The implant-to-abutment connection should not be altered. Single-crown restoration Crown-splinting 16
IMPLANT-SUPPORTED BRIDGES Implant-supported bridges can be inserted wherever an implantation is impossible. Implant distribution should be structured in such a way that spanned segments are kept small. Examples of bridge positioning Initial situation Abutments in a lab analog Prepared abutments Cement-retained bridge CONELOG ® SCREW-LINE IMPLANT Development of a uniform insertion direction for the crown block should be part of the abutment preparation. The implant-to-abutment connection should not be altered. 17
Page 1 and 2: CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15: BIOLOGICAL WIDTH After protocol-spe
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43 and 44: Manual tapping is performed with ta
Page 45 and 46: IMPLANT POSITIONING Protocol-compli
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58: IMPRESSION-TAKING INTRODUCTION CONE
Page 59 and 60: OPEN-TRAY IMPRESSION-TAKING METHOD
Page 61 and 62: CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68:
FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70:
FURTHER DOCUMENTATION further infor
Page 71 and 72:
CONELOG ® SCREW-LINE IMPLANT TRADE
show all

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?