CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT <strong>SURGICAL</strong> PROCEDURE PRE-DRILLING A tapered pre-drill SCREW-LINE with a coronal diameter of 2.8 mm and apical diameter of 1.7 mm is available for the SCREW-LINE configuration. Recommended drilling speed: 600 rpm. The depth marks on the drill match the implant lengths 7/9/11 and 13 mm. The maximum drilling depth is 16 mm. for safety reasons, a depth stop matching the proposed implant length should be used. further drilling is performed with the form drills. Pre-drill SCREW-LINE: Ø 1.7–2.8 mm Pre-drilling Checking the axial orientation after pre-drilling Ø 1.7–2.8 mm 38 max. 600 rpm 2.8 mm 1.7 mm Paralleling pin SCREW-LINE 2.0 mm 2.8 mm 1.7 mm
FORM DRILLING Diameters and lengths Diameter- and length-calibrated form drills with reduced drill coil are available for each implant size. The form drills are color-coded and laser-marked. The form drills included in the surgery sets are supplied with a color-coded, removable depth stop. This must only be used with form drills SCREW-LINE. Depending on the specified drilling depth (implant length), the hole diameter is expanded progressively with the series of form drills until the intended implant diameter is achieved. Recommended drilling speeds: Ø 3.3 mm 550 rpm Ø 3.8 mm 500 rpm Ø 4.3 mm 400 rpm Ø 5.0 mm 350 rpm The protocol-specified insertion depth for SCREW-LINE implants, with depth stops in place, is the implant length (7/9/11/13/16 mm) minus 0.4 mm with the circular stop at the bone level, so that the implant shoulder extends 0.4 mm above the ridge. The preparation is performed using the laser marks (black) as guides. The marks are spaced 1.0 mm apart. The mark widths are 0.4 mm. Ø 3.3 mm Ø 3.8 mm Ø 4.3 mm Ø 5.0 mm form drill SCREW-LINE CONELOG ® SCREW-LINE IMPLANT Length 7 mm 9 mm 11 mm 13 mm 16 mm 0.4 mm 0.4 mm 0.4 mm 1 mm 1 mm 1 mm 39
Page 1 and 2: CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37: PUNCH-MARKING THE CORTICAL BONE The
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43 and 44: Manual tapping is performed with ta
Page 45 and 46: IMPLANT POSITIONING Protocol-compli
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58: IMPRESSION-TAKING INTRODUCTION CONE
Page 59 and 60: OPEN-TRAY IMPRESSION-TAKING METHOD
Page 61 and 62: CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68: FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70: FURTHER DOCUMENTATION further infor
Page 71 and 72: CONELOG ® SCREW-LINE IMPLANT TRADE

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?