CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT IMPRESSION-TAKING CONELOG ® IMPRESSION POSTS, CLOSED TRAY Art. No. C2110.3300 C2110.3800 C2110.4300 C2110.5000 CONELOG ® impression posts, closed tray, including impression cap, bite registration cap and fixing screw for implant Ø 3.3 mm 3.8 mm 4.3 mm 5.0 mm PH mm 10.7 mm 10.7 mm 10.7 mm 10.7 mm PH: Prosthetic height SPARE IMPRESSION CAP Art. No. J2111.3300 J2111.3800 J2111.4300 J2111.5000 Impression cap for impression posts, closed tray (5 units) for implant Ø 3.3 mm 3.8 mm 4.3 mm 5.0 mm REQUIRED INSTRUMENTS/LAB ANALOGS: Screwdrivers, hex, extra short/short/long 58 CONELOG ® lab analogs, Ø 3.3/3.8/4.3/5.0 mm IMPORTANT NOTE All components for impression-taking of CONELOG ® implants are designed for single use and must not be modified. CONELOG ® lab analogs with two retention notches
OPEN-TRAY IMPRESSION-TAKING METHOD The open-tray impression-taking method requires a custom-made impression tray that is perforated for the protrusion of the fixing screw extending from the implant axis. CONELOG ® impression posts, open tray The fixing screw is secured in the CONELOG ® impression post with an O-ring and must only be tightened by hand using the screwdriver, hex, both in the CONELOG ® implant as well as in the CONELOG ® lab analog. NOTE Before removing the impression, the loosened screw must be withdrawn until you can feel the limit stop (O-ring). Otherwise the axis divergences of the implant can make removing the impression difficult or can deform the impression due to the high compression. Impressions can be taken with implant axis divergences of up to 20° (10° for each CONELOG ® implant). The fixing screw is equipped with a predetermined breaking point. If space limitations are encountered, it can be shortened by 3.0 mm by breaking it off with a screwdriver, hex. Caution: shorten extra-orally only! 3.0 mm O-ring 10.0 mm CONELOG ® SCREW-LINE IMPLANT O-ring 59
Page 1 and 2:
CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4:
TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6:
CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43 and 44: Manual tapping is performed with ta
Page 45 and 46: IMPLANT POSITIONING Protocol-compli
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57: IMPRESSION-TAKING INTRODUCTION CONE
Page 61 and 62: CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68: FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70: FURTHER DOCUMENTATION further infor
Page 71 and 72: CONELOG ® SCREW-LINE IMPLANT TRADE
show all

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?