CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT IMPRESSION-TAKING CONELOG ® IMPRESSION POST INSERTION The healing cap or temporary restoration is removed. The impression post open-tray is placed on the implant and the fixing screw is gently tightened. The impression post is rotation-symmetrical and does not require any specific orientation. Carefully rotate the impression post in the implant until the cams engage with the grooves of the implant. Tighten the fixing screw manually with the screwdriver, hex. We recommend taking an x-ray to check that the impression post is seated correctly before taking the impression, particularly where gingiva is thight and thick. 60 CAUTION! Height difference if cams are not snapped into place is approx. 0.6 mm!
CONELOG ® SCREW-LINE IMPLANT IMPRESSION-TAKING Before taking the impression, check the tray for a precision fit. The fixing screws protruding from the perforations must not touch the tray. Next, the impression is taken with silicone or polyether impression material. To remove the impression, loosen the fixing screw, pull it back and then lift off the impression. TIP: To simplify the procedure, we recommend sending the laboratory the corresponding CONELOG ® lab analog as well. 61
Page 1 and 2:
CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4:
TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6:
CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8:
THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43 and 44: Manual tapping is performed with ta
Page 45 and 46: IMPLANT POSITIONING Protocol-compli
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58: IMPRESSION-TAKING INTRODUCTION CONE
Page 59: OPEN-TRAY IMPRESSION-TAKING METHOD
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68: FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70: FURTHER DOCUMENTATION further infor
Page 71 and 72: CONELOG ® SCREW-LINE IMPLANT TRADE
show all

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?