CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT <strong>SURGICAL</strong> PROCEDURE IMPLANTATION IMPLANT INSERTION The CONELOG ® SCREW-LINE implant is taken by the sterile handle and removed from the primary package (blister). Contamination from nonsterile parts must be avoided. 46 CAUTION! Before inserting the implant, the silicone plug and the CONELOG ® cover screw must be removed from the handle. Taking the implant by the handle, insert it into the implant bed. Make sure to observe the axial orientation of the implant bed. If a hole has been pretapped, the positions of the thread dog point in the cortical bone must match that on the implant. TIP: Carefully screw the implant to the left until you can feel the thread dog point. Then, using the handle, screw the implant to the right until it obtains sufficient grip to allow withdrawal of the handle. OPTIONAL ACCESSORIES: PICKUP INSTRUMENT If the intraoral space is insufficient to allow insertion of the implant with the handle, the implant can be removed from the handle using the PickUp instrument. Slide the PickUp instrument between the implant and handle onto the CONELOG ® insertion post and lift off the handle. for the insertion procedure, place the selected driver on the CONELOG ® insertion post. The implant is inserted into the bone, and the PickUp instrument is removed. Inserting the implant
Placing the PickUp on the CONELOG ® insertion post Locked-on PickUp Removing the handle CONELOG ® SCREW-LINE IMPLANT Inserting the implant Mounting the driver and removing the PickUp 47
Page 1 and 2: CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43 and 44: Manual tapping is performed with ta
Page 45: IMPLANT POSITIONING Protocol-compli
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58: IMPRESSION-TAKING INTRODUCTION CONE
Page 59 and 60: OPEN-TRAY IMPRESSION-TAKING METHOD
Page 61 and 62: CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68: FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70: FURTHER DOCUMENTATION further infor
Page 71 and 72: CONELOG ® SCREW-LINE IMPLANT TRADE

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?