CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT <strong>SURGICAL</strong> PROCEDURE TAPPING All CONELOG ® SCREW-LINE implants come with a self-tapping thread with abrasive-blasted, acid-etched surface (Promote ® ). Use of a tap is recommended for bone quality categories 1 and 2 (Lekholm & Zarb, 1985). The maximum speed must not exceed 15 rpm when performing power- assisted tapping. We recommend manual tapping. Ø 3.3 mm Ø 3.8 mm Ø 4.3 mm Ø 5.0 mm Tap SCREW-LINE, with hexagon, max. 15 rpm 42
Manual tapping is performed with tap adapters for the taps SCREW-LINE and the locked torque wrench.Make sure to pay attention to the axial direction of the implant bed when inserting and removing the tap. The limit for insertion of the tap is the upper edge of the cutting blade. Locked torque wrench Tap adapter, short, long CONELOG ® SCREW-LINE IMPLANT 43
Page 1 and 2: CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41: FORM DRILLING After pre-drilling is
Page 45 and 46: IMPLANT POSITIONING Protocol-compli
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58: IMPRESSION-TAKING INTRODUCTION CONE
Page 59 and 60: OPEN-TRAY IMPRESSION-TAKING METHOD
Page 61 and 62: CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68: FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70: FURTHER DOCUMENTATION further infor
Page 71 and 72: CONELOG ® SCREW-LINE IMPLANT TRADE

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?