CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT GENERAL SYSTEM INFORMATION ABOUT THE CAMLOG ® /CONELOG ® IMPLANT SYSTEM 4 THE CAMLOG ® /CONELOG ® IMPLANT SYSTEM The CONELOG ® Implant System has been developed on the basis of many years of clinical and laboratory experience. It is a user-friendly, consistently prosthesis-oriented implant system. All CAMLOG ® and CONELOG ® products are always manufactured with the most state-of-the-art technology. The CAMLOG ® /CONELOG ® Implant System is continuously being developed by the company’s research and development team in collaboration with clinics, universities and dental technicians and therefore stays abreast of the latest technology. The CAMLOG ® Implant System is very well-documented scientifically. Studies support this with respect to a great many parameters including the implant surface, time of implantation and/or implant loading, primary stability, connection design or type of superstructure. The long-term results of the CAMLOG ® Implant System are convincing. IMPORTANT NOTE The descriptions that follow are not adequate to permit immediate use of the CAMLOG ® /CONELOG ® Implant System. Instruction by a surgeon experienced in using the CAMLOG ® /CONELOG ® Implant System is strongly recommended. CAMLOG ® /CONELOG ® dental implants and abutments should only be used by dentists, physicians, surgeons and dental technicians who have been trained in using the system. CAMLOG regularly offers relevant courses and training sessions. Methodical errors made during the treatment can result in loss of the implant and significant loss of the peri-implant bone.
CONELOG ® SCREW-LINE IMPLANTS INTRODUCTION CONELOG ® SCREW-LINE implants are endosseous implants available in various lengths and diameters. The implants are surgically inserted in the bone of the maxilla and/or mandible and serve as an anchor for functional and esthetic oral restorations for partially and fully edentulous patients. The prosthetic restoration is performed with single crowns, bridges or full dentures that are attached to the CONELOG ® implants with the appropriate CONELOG ® components. In principle, there are no preferable areas of insertion. The CONELOG ® SCREW-LINE implant is a geometrically tapered, self-tapping screw implant and is available with Promote ® surface. IMPLANTATION The CONELOG ® SCREW-LINE implant is not only suitable for late implantation, but for immediate or delayed immediate implantation as well. The healing technique can be submerged or transgingival. The implant is easily inserted because the taper of the implant body (3°–9° depending on length and diameter) induce self centering. The self-cutting thread provides for continuous grip on the bone and high primary stability. IMPORTANT NOTE The procedure for preparing the implant bed for CONELOG ® SCREW-LINE implants is identical to that performed with CAMLOG ® SCREW-LINE implants. The implant bed is prepared using SCREW-LINE drills and instruments. RANGE OF USE FOR CONELOG ® SCREW-LINE IMPLANTS: A more deeply positioned coronal implant shoulder is recommended particularly where a high-esthetic outcome is important. The CONELOG ® SCREW-LINE implant, Promote ® plus, has an acid-etched tapered implant shoulder (45°). The following clinical requirements should be met: • Normal to thick biotype • Gingival height of at least 3.0 mm • Minimum width of 1.0 mm of the attached gingiva • Minimum distance of 2.0 mm between attached gingiva and mimetic musculature CONELOG ® SCREW-LINE Implant Promote ® plus Machined implant shoulder surface CONELOG ® SCREW-LINE IMPLANT Acid-etched tapered implant shoulder (45°) Height: 0.1–0.2 mm (variable according to implant Ø) Abrasive-blasted, acid-edged Promote ® surface (Micro-Macro surface) 5
Page 1 and 2: CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43 and 44: Manual tapping is performed with ta
Page 45 and 46: IMPLANT POSITIONING Protocol-compli
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56:
HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58:
IMPRESSION-TAKING INTRODUCTION CONE
Page 59 and 60:
OPEN-TRAY IMPRESSION-TAKING METHOD
Page 61 and 62:
CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64:
NOTE After the impression post has
Page 65 and 66:
The registration of the habitual ja
Page 67 and 68:
FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70:
FURTHER DOCUMENTATION further infor
Page 71 and 72:
CONELOG ® SCREW-LINE IMPLANT TRADE
show all

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?