CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT CONELOG ® IMPLANT POSITION 32 PLANNING OVERVIEW OF DRILL SEQUENCES IMPLANT BED PREPARATION Overview: • Punch-mark the desired implant position with the Ø 2.3 mm round bur • Deep drill along the implant axial line with the Ø 2.0 mm pilot drill • Check with the Ø 1.7–2.8/2.0 mm paralleling pin with depth marks • Pre-drill with the Ø 1.7–2.8 mm pre-drill • Check with the Ø 1.7–2.8/2.0 mm paralleling pin with depth marks • Shape with the form drill • Probe the implant bed hole for its bony end • Cortical bone drilling (for bone quality 1*) • Tap SCREW-LINE (for bone quality 1 and 2*) OptIONaL fOr aLL dIamEtErs plus 1.0 mm 1.0 mm Promote 0.4 mm We recommend using the tap for bone qualities 1* and 2*. form drills cortical bone allow implants to be inserted in the cortical bone at a lower torque for bone quality 1*. CB:Cortical Bone *Bone quality as documented in Lekholm & Zarb, 1985 ® Ø 3.3 mm Round bur Ø 2.3 mm Pilot drill Ø 2.0 mm 16 mm 13 mm 11 mm 9 mm rpm 800 800 Ø 3.8 mm rpm U/min 800 800 Ø 4.3 mm Ø 5.0 mm Round bur Ø 2.3 mm Round bur Ø 2.3 mm rpm 800 800 Round bur Ø 2.3 mm Pilot drill Ø 2.0 mm 16 mm 13 mm 11 mm 9 mm 7 mm Pilot drill Ø 2.0 mm 16 mm 13 mm 11 mm 9 mm 7 mm Pilot drill Ø 2.0 mm 16 mm 13 mm 11 mm 9 mm 7 mm rpm 800 800 Depth stop Depth stop Depth stop Depth stop Paralleling pin Depth measurement Paralleling pin Depth measurement Paralleling pin Depth measurement Paralleling pin Depth measurement
Pre-drill Ø 1.7 – 2.8 mm 16 mm 13 mm 11 mm 9 mm Pre-drill Ø 1.7 – 2.8 mm 16 mm 13 mm 11 mm 9 mm 7 mm Pre-drill Ø 1.7 – 2.8 mm 16 mm 13 mm 11 mm 9 mm 7 mm Pre-drill Ø 1.7 – 2.8 mm 16 mm 13 mm 11 mm 9 mm 7 mm Depth stop Paralleling pin Form drill Form drill Ø 3.3 mm Ø 3.3 mm 600 550 550 15 Depth stop Paralleling pin 600 550 500 500 15 Depth stop Paralleling pin Paralleling pin Form drill Ø 3.3 mm 600 550 500 400 400 15 Depth stop Form drill Ø 3.3 mm 600 550 500 400 350 350 15 Ø 3.8 mm Ø 3.8 mm Ø 3.8 mm Ø 4.3 mm Ø 4.3 mm Ø 5.0 mm * Form drill Cortical Bone * Form drill Cortical Bone * Form drill Cortical Bone * Form drill Cortical Bone * Tap * Tap * Tap * Tap CONELOG ® SCREW-LINE IMPLANT Promote ® plus Promote ® plus Promote ® plus Promote ® plus 33
Page 1 and 2: CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31: DRILLING SPEEDS The drill speed dep
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43 and 44: Manual tapping is performed with ta
Page 45 and 46: IMPLANT POSITIONING Protocol-compli
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58: IMPRESSION-TAKING INTRODUCTION CONE
Page 59 and 60: OPEN-TRAY IMPRESSION-TAKING METHOD
Page 61 and 62: CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68: FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70: FURTHER DOCUMENTATION further infor
Page 71 and 72: CONELOG ® SCREW-LINE IMPLANT TRADE

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?