CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT <strong>SURGICAL</strong> PROCEDURE IMPLANT PACKAGING The CONELOG ® implant packaging consists of three components: • Gray CONELOG ® outer packaging (cardboard) with label • Transparent peel-back pouch • Transparent primary package (blister, sterile) with label 44 CONELOG ® SCREW-LINE implants are double-sterile packaged. The primary package (blister) contains the implant with pre-installed CONELOG ® insertion post and mounted transparent handle. Outer package with label Peel-back pouch Primary package (sterile) with label (blister pack) Primary package with visible implant Opened primary package with implant and mounted handle Cover screw located in the handle System information on the label
IMPLANT POSITIONING Protocol-compliant insertion depth of CONELOG ® SCREW-LINE implants with attached depth stop is achieved when the machined plane surface of the implant extends 0.4 mm above the crestal bone level and one of the three groove marks indicates the specified prosthetic position. If it was decided to set preparation depths for the implants individually by removing the depth stop during form drilling, this must be kept in mind when inserting the implant. It is possible to individually position implants vertically to match the drilling depth. GROOVE POSITIONING Corresponding to the three grooves of the implant-abutment connection, marks are inscribed on the drivers for the SCREW-LINE Implants. These permit a check of the groove positions during the insertion and their orientation as required for the prosthesis. If the dental technician has not indicated the groove position, a vestibular orientation is advantageous in most cases since the angle of angulated abutments originates at a groove. NOTE Keep in mind during positioning of the grooves that turning to the next groove position (120°) will cause the screw implant to be inserted about 0.2 mm deeper. Driver Groove marking Cam Groove CONELOG ® insertion post Vestibular orientation of the groove CONELOG ® SCREW-LINE implant CONELOG ® SCREW-LINE IMPLANT 45
Page 1 and 2: CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43: Manual tapping is performed with ta
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51 and 52: ACCESSORIES CONELOG ® ADAPTER FOR
Page 53 and 54: ACCESSORIES After unscrewing the re
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58: IMPRESSION-TAKING INTRODUCTION CONE
Page 59 and 60: OPEN-TRAY IMPRESSION-TAKING METHOD
Page 61 and 62: CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68: FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70: FURTHER DOCUMENTATION further infor
Page 71 and 72: CONELOG ® SCREW-LINE IMPLANT TRADE

CONELOG® SURGICAL PROCEDURES - Camlog

Create successful ePaper yourself

Delete template?

Save as template?