CONELOG® SURGICAL PROCEDURES - Camlog

More documents

Recommendations

Info

CONELOG ® SCREW-LINE IMPLANT <strong>SURGICAL</strong> PROCEDURE ACCESSORIES After unscrewing and removing the CONELOG ® insertion post, slide the diameter-matched CONELOG ® adapter into the implant until the cams engage the with the grooves. The retention screw on the adapter is used to fix in place (manual tightening). After removing the sleeve, the CONELOG ® SCREW-LINE implant can be inserted. Placing the CONELOG ® adapter for the insertion, place the locked torque wrench over the hexagon of the CONELOG ® adapter and screw the implant to its final position, making sure to line it up with the notched mark. Inserting the implant Placing the torque wrench Tightening the implant to final position 52 Tightening the retention screw Opening the hemostatic clip and removing the sleeve CONELOG ® SCREW-LINE implant attached to CONELOG ® adapter
ACCESSORIES After unscrewing the retention screw, detach the CONELOG ® adapter from the CONELOG ® SCREW-LINE implant. After removing the silicone plug from the pre-fastened handle of the implant, pick up the CONELOG ® cover screw with the screwdriver hex and insert it into the implant tighten manually (danger of aspiration!). Unscrewing the retention screw Removing the CONELOG ® adapter CONELOG ® SCREW-LINE implant with CONELOG ® cover screw Wound closure CONELOG ® SCREW-LINE IMPLANT The CONELOG ® cover screw must not be power-tightened. A CONELOG ® healing cap should be used for the transgingival healing (see pages 54–56). Inserting the CONELOG ® cover screw 53
Page 1 and 2: CONELOG ® SCREW-LINE IMPLANT BASIC
Page 3 and 4: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: CONELOG ® SCREW-LINE IMPLANTS INTR
Page 7 and 8: THE CONELOG ® IMPLANT SYSTEM SYSTE
Page 9 and 10: CONELOG ® DISCONNECTOR FOR CONELOG
Page 11 and 12: TEAM APPROACH Increasingly higher d
Page 13 and 14: ESTHETICS The use of therapeutic me
Page 15 and 16: BIOLOGICAL WIDTH After protocol-spe
Page 17 and 18: IMPLANT-SUPPORTED BRIDGES Implant-s
Page 19 and 20: PLANNING INTRODUCTION Modern implan
Page 21 and 22: LABORATORY CAST ANALySES It is esse
Page 23 and 24: WAX-UP/SET-UP The wax-up or set-up
Page 25 and 26: PLANNING WITH ORTHOPANTOMOGRAPH/ DE
Page 27 and 28: IMPLANT POSITION VERIFICATION FINAL
Page 29 and 30: SURGERY SET CAMLOG ® /CONELOG ® S
Page 31 and 32: DRILLING SPEEDS The drill speed dep
Page 33 and 34: Pre-drill Ø 1.7 - 2.8 mm 16 mm 13
Page 35 and 36: IMPLANT BED PREPARATION Shaping the
Page 37 and 38: PUNCH-MARKING THE CORTICAL BONE The
Page 39 and 40: FORM DRILLING Diameters and lengths
Page 41 and 42: FORM DRILLING After pre-drilling is
Page 43 and 44: Manual tapping is performed with ta
Page 45 and 46: IMPLANT POSITIONING Protocol-compli
Page 47 and 48: Placing the PickUp on the CONELOG
Page 49 and 50: Next, unscrew the retention screw o
Page 51: ACCESSORIES CONELOG ® ADAPTER FOR
Page 55 and 56: HEALING OPTIONS CONELOG ® HEALING
Page 57 and 58: IMPRESSION-TAKING INTRODUCTION CONE
Page 59 and 60: OPEN-TRAY IMPRESSION-TAKING METHOD
Page 61 and 62: CONELOG ® SCREW-LINE IMPLANT IMPRE
Page 63 and 64: NOTE After the impression post has
Page 65 and 66: The registration of the habitual ja
Page 67 and 68: FABRICATION OF A TEMPORARY SINGLE-T
Page 69 and 70: FURTHER DOCUMENTATION further infor
Page 71 and 72: CONELOG ® SCREW-LINE IMPLANT TRADE

CONELOG® SURGICAL PROCEDURES - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?