HC950 • HC950 SSP HC970 • HC970 SSP - Wagner

More documents

Recommendations

Info

Cleaning the unit (shutting down)8. Cleaning the unit (shutting down)A clean state is the best method of ensuring operation withoutproblems. After you have finished spraying, clean the unit. Under nocircumstances may any remaining coating material dry and harden inthe unit.The cleaning agent used for cleaning (only with an ignition pointabove 21 °C) must be suitable for the coating material used.• Secure the spray gun, refer to the operating manual of thespray gun.Clean and remove tip.For a standard tip, refer to page 43, point 11.2.If a non-standard tip is installed, proceed according to the relevantoperating manual.1. Push locking pin and swivel material feed pump out ofcoating material.2. Pull the trigger of the spray gun in order to pump theremaining coating material from the suction tube, highpressurehose and the spray gun into an open container.AttentionThe container must be earthed in case of coatingmaterials which contain solvents.Caution! Do not pump or spray into a container witha small opening (bunghole)!Refer to the safety regulations.3. Push locking pin and swivel material feed pump to a containerwith suitable cleaning agent.4. Turn the relief valve handle fully counterclockwise (kCirculation).5. Pump a suitable cleaning agent in the circuit for a fewminutes.6. Turn relief valve handle fully clockwise (p spray).7. Pump the remaining cleaning agent into an open containeruntil the unit is empty.8. Turn the relief valve handle fully counterclockwise (kCirculation).9. Move the hydraulic ball valve on the material feed pump to itshorzontal position (closed).10. Turn off the gasoline engine or electric motor.GB8.1 Cleaning the unit from the outsideAttentionGasoline units — Switch off the gasoline engine andlet it cool down.Electric units — Unplug the mains plug from thesocket.Danger of short-circuits through penetrating water.Never spray down the unit with high-pressure orhigh-pressure steam cleaners.Do not put the high-pressure hose into solvents.Use only a wet cloth to wipe down the outside of thehose.Wipe the unit off with a cloth soaked in a suitable cleaning agent.8.2 Cleaning the high-pressure filterClean the filter cartridge regularly.A soiled or clogged high-pressure filter can cause a poor spraypattern or a clogged tip.Disassembly1. Move the hydraulic ball valve on the material feed pump to itshorzontal position (closed).Flow of hydraulic oil to hydraulic motor of material feed pumpis interrupted.2. Turn the relief valve handle fully counterclockwise (kCirculation).3. Turn off the gasoline engine or electric motor.4. Unscrew the housing cover (fig. 15, item 1).5. Pull filter cartridge (3) out of housing (8).6. Clean the pressure spring (2) and filter cartridge (3) with anappropriate cleaning agent, clean the inside of the housing (8)and housing cover (1).7. Check ball in the filter cartridge (3) for wear and replace filtercartridge, if necessary.8. If ball in filter cartridge (3) is thoroughly worn, aremove O-ring(6) and valve seat (7). Replace worn valve seat, if necessary.9. Always replace O-ring (6) after removal.10. Pull off pressure spring (2) from housing cover (1).Measure length of pressure spring, and replace if shorter than19 mm.Assembly1. Insert valve seat (7) with the ball seat surface facing up intothe housing (8).2. Insert O-ring (6) into the housing (8).3. Insert filter cartridge (3).4. Place thin seal (5) on threaded section of housing (8).5. Place thick seal (4) on top of thin seal (5).6. Slide pressure spring (2) onto housing cover pin (2).7. Screw on housing cover (1) and tighten by hand.38 HC 950 • HC 970
1234567GB8.3 Cleaning Airless spray gunCleaning the unit (shutting down)– Rinse Airless spray gun with an appropriate cleaning agent.– Clean tip thoroughly with appropriate cleaning agent so thatno coating material residue remains.– Thoroughly clean the outside of the Airless spray gun.Intake filter in Airless spray gun (fig. 16)Dismounting1. Pull protective guard (1) forward vigorously.2. Screw handle (2) out of the gun housing. Remove intake filter(3).3. Intake filter congested or defective – replace.Mounting1. Place intake filter (3) with the long cone into the gun housing.2. Screw handle (2) into the gun housing and tight en.3. Snap in protective guard (1).8132HC 950 • HC 970 39
Page 1 and 2: DGBFIBetriebsanleitungOperating man
Page 3 and 4: InhaltDInhaltSeite1. Sicherheitsvor
Page 5 and 6: • Das Spritzgerät in ausreichend
Page 7 and 8: Anwendungsübersicht2. Anwendungsü
Page 9 and 10: 3.5 Legende zum Erklärungsbild HC-
Page 11 and 12: 3.8 Technische Daten HC-Geräte mit
Page 13 and 14: 4. Inbetriebnahme4.1 Position der M
Page 15 and 16: InbetriebnahmeDArbeitsunterbrechung
Page 17 and 18: 1234567DGerätereinigung (Außerbet
Page 19 and 20: DHilfe bei Störungen9.4 Materialf
Page 21 and 22: 11. AnhangDAnhang11.1 Düsenauswahl
Page 23 and 24: DAnhangAnwendung Düsenmarkierung S
Page 25 and 26: BerlinJ. Wagner GmbHService-Stützp
Page 27 and 28: ContentsGBContentsPage1. Safety reg
Page 29 and 30: • Follow material and solvent man
Page 31 and 32: General view of application2. Gener
Page 33 and 34: 3.5 Illustration legend for electri
Page 35 and 36: 3.8 Technical data for electric HC
Page 37 and 38: 4. Starting operation4.1 Changing t
Page 39: Starting operationGBInterruption of
Page 43 and 44: GBRemedy in case of faults9.4 Mater
Page 45 and 46: 11. Appendix11.1 Selection of tipTo
Page 47 and 48: GBAppendixApplication Tip marking S
Page 49 and 50: ABCHDJ. Wagner Ges.m.b.H.Ottogasse
Page 51 and 52: ContenuPage1. Prescriptions de séc
Page 53 and 54: tuyau au besoin). Les vapeurs infla
Page 55 and 56: Géneralités d’utilisation2. Gé
Page 57 and 58: 3.5 Légende de l’illustration gr
Page 59 and 60: FDescription du matériel3.8 Caract
Page 61 and 62: 4. Mise en service4.1 Changement de
Page 63 and 64: Mise en serviceFInterruptions de tr
Page 65 and 66: 1234567F8.3 Nettoyage du pistolet A
Page 67 and 68: FDépannage9.4 Pompe de produitPann
Page 69 and 70: 11. Annexe11.1 Choix des busesPour
Page 71 and 72: FAnnexeUtilisation Marquage Angle d
Page 73 and 74: ABCHDJ. Wagner Ges.m.b.H.Ottogasse
Page 75 and 76: IndicePagina1. Norme di sicurezza p
Page 77 and 78: terreno deve essere molto ben areat
Page 79 and 80: Panoramica sull’impiego2. Panoram
Page 81 and 82: 3.5 Leggenda della figura illustrat
Page 83 and 84: 3.8 Dati tecnici apparecchi HC con
Page 85 and 86: 4. Messa in servizio4.1 Modifica de
Page 87 and 88: Messa in servicioIInterruzione del
Page 89 and 90: 1234567IPulizia dell’apparecchio
Page 91 and 92:
IEliminazione di anomalie9.4 Pompa
Page 93 and 94:
11. AppendiceIAppendice11.1 Scelta
Page 95 and 96:
IAppendiceImpiegoMarcaturadell'ugel
Page 97 and 98:
ABCHDJ. Wagner Ges.m.b.H.Ottogasse
Page 99 and 100:
Illustration des pièces de rechang
Page 101 and 102:
Pos. HC 950HC 950-SSP HC 970HC 970-
Page 103 and 104:
Pos. HC950 HC950-SSP HC970 HC970-SS
Page 105 and 106:
Pos.HC950HC950-SSPHC970HC970-SSPdBe
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Pos. HC950-SSP HC970-SSPdBenennungg
Page 115 and 116:
Page 117 and 118:
Pos.HC 950HC 950-SSPHC 970HC 970-SS
Page 119 and 120:
Ersatzteilbild Spare parts diagram
Page 121 and 122:
Schaltplan Electrical Schematic Sch
Page 123 and 124:
Important notes on product liabilit
Page 125 and 126:
Avvertenza importante sulla respons
Page 127 and 128:
J. Wagner GmbH Otto Lilienthal-Str.
Page 129 and 130:
J. Wagner GmbH Otto Lilienthal-Str.
Page 131:
Consignes d’élimination:Selon la
show all

HC950 • HC950 SSP HC970 • HC970 SSP - Wagner

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?