Strata DK 16 Manual
Strata DK 16 Manual
Strata DK 16 Manual
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
INSTALLATION-STATION APPARATUS<br />
SECTION 100-8<strong>16</strong>-206<br />
MARCH 1993<br />
4) Connect the telephone to the wall modular<br />
connector with a cord approximately four<br />
inches long (available at most telephone sup-<br />
ply companies). Route the cord into the hol-<br />
low portion of the base.<br />
5) Mount the telephone on the wall mounting<br />
modular connector plate.<br />
3 DIGITAL TELEPHONE UPGRADES<br />
3.00 This section describes how to upgrade and<br />
configure 2000- and lOOO-series Digital Tele-<br />
phones for features and options.<br />
3.10 Simultaneous Voice and Data Upgrade<br />
(PDIU-D12 and PDIU-DI)<br />
3.11 Both the 2000- and 1 OOO-series Digital Tele-<br />
phones can be upgraded with an integrated data<br />
interface unit to transmit and receive simultaneous<br />
voice and data calls. There are two versions of the<br />
integrated unit: the PDIU-DI and the PDIU-D12.<br />
The 2000-series telephones can only be equipped<br />
with a PDIU-D12, and the 1 OOO-series telephones<br />
can only be equipped with a PDIU-DI. Asynchro-<br />
nous devices, such as personal computers (PC)<br />
and terminals, can be connected to the standard<br />
RS-232 connector of the PDIUDl(2). Station us-<br />
ers are able to transmit and receive W-232 data<br />
over the single wire pair of the PDIUDI(2)-equipped<br />
telephone.<br />
3.12 Data calls can be manually dialed with a<br />
Data Call button and disconnected with a Data<br />
Release button on the telephone; or, data and<br />
voice calls can be dialed from the keyboard of the<br />
terminal or PC using standard “AT” commands.<br />
Digital telephones may also be assigned a Modem<br />
button to reserve a modem or monitor modem<br />
availability and status. Assign feature buttons to<br />
telephones with Program 39.<br />
NOTES:<br />
1. 1 OOO- and2000series Digital Telephones<br />
equipped with a PDIUDl(2) cannot be<br />
wall-mounted or equipped with an Add-<br />
On-Module (ADM), or DVSU for OCA. A<br />
2000series digital telephone equipped<br />
6-4<br />
with a PDIU-Dl2 can support an HHEU at<br />
the same time, but cannot support a<br />
DVSU. A 1000~series Digital Telephone<br />
equipped with a PDIU-DI cannot support<br />
an HHEU, ADM, or a DVSU for OCA.<br />
2. P<strong>DK</strong>Ul circuits 1 - 7 only can support<br />
PDIU-Dl(2)s, but all P<strong>DK</strong>U2and base unit<br />
digital circuits, can support PDIU-Dl(2)s.<br />
3.13 PDIU-Dl(2) Installation. Install the inte-<br />
grated data interface unit (PDIU-DI for 1 OOO-series<br />
and PDIU-D12 for 2000series) in accordance with<br />
the following steps:<br />
1)<br />
2)<br />
3)<br />
4)<br />
5)<br />
Loosen the four captive screws securing the<br />
digital telephone base and remove it (Figure<br />
6-l).<br />
Refer to Figure 6-4for 2000series telephones<br />
or Figure 6-5 for 1 OOO-series telephones, and<br />
insert the two integrated unit wire plugs into<br />
the connectors on the printed circuit board<br />
(PCB) in the telephone (observing the red<br />
wire for correct positioning).<br />
Attach the integrated unit to the bottom of the<br />
telephone and secure with the four captive<br />
screws.<br />
Remove the telephone number directory tray<br />
from the original telephone base and install it<br />
on the integrated unit telephone base. Bend<br />
the tray by squeezing its sides so it bows<br />
slightly to remove and re-install (Figure 6-4 or<br />
6-5).<br />
Check Table 8-D in Section 100-8<strong>16</strong>-208;<br />
install 2-pair house cable (or external power)<br />
and 2-pair modular cord (supplied with PDIU-<br />
DI) if required to achieve maximum distance.<br />
3.14 Integrated Data Interface Unit Program-<br />
ming Overview<br />
Program 39<br />
l Assigns the Data Call, Data Release, and Mo-<br />
dem buttons.<br />
Programs 20 and 22<br />
l Used for data interface unit assignments.